|
[Sponsors] |
February 13, 2020, 07:47 |
Oxidation in Ansys
|
#1 |
New Member
Karthikeyan
Join Date: Feb 2020
Posts: 6
Rep Power: 6 |
Hi,
Can anyone tell me how to do oxidation in ansys? I am trying to find a method for long time but didnt find it till now. |
|
February 13, 2020, 08:33 |
Too generic
|
#2 |
Senior Member
|
Oxidation is a very generic term; oxidation of C gives flame while oxidation of Fe gives rust. A little more elaboration would be very helpful.
__________________
Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority. |
|
February 13, 2020, 09:35 |
Oxidation
|
#3 |
New Member
Karthikeyan
Join Date: Feb 2020
Posts: 6
Rep Power: 6 |
I need to simulated oxidation to determine the amount of corrosion in materials coated.
|
|
February 13, 2020, 10:34 |
EC reactions
|
#4 |
Senior Member
|
Corrosion is result of electrochemical reactions. You can use EC reactions within Fluent's species model to do that.
__________________
Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority. |
|
February 13, 2020, 10:36 |
Oxidation
|
#5 |
New Member
Karthikeyan
Join Date: Feb 2020
Posts: 6
Rep Power: 6 |
But, I cant change any complex material right? Do you have some examples if possible can you share it with me?
|
|
February 13, 2020, 10:45 |
Material
|
#6 |
Senior Member
|
I am afraid I don't completely understand what you mean by complex material.
__________________
Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority. |
|
February 13, 2020, 10:46 |
|
#7 |
New Member
Karthikeyan
Join Date: Feb 2020
Posts: 6
Rep Power: 6 |
Like a composites or mixture of composites. Layers of the composites. FLuent cant use two or three layer of materials
|
|
February 13, 2020, 10:51 |
Surface Reactions
|
#8 |
Senior Member
|
I assume by layers you mean layers of solid material. The oxidation reactions occur only on the surface, hence, layers do not matter. As far as, simulating layers is concerned, you can have multiple layers without any issue.
__________________
Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority. |
|
February 13, 2020, 10:54 |
|
#9 |
New Member
Karthikeyan
Join Date: Feb 2020
Posts: 6
Rep Power: 6 |
do you have any examples, just for an simple material, I can expand it.
|
|
February 13, 2020, 11:00 |
Apologies
|
#10 |
Senior Member
|
I am sorry. I do not have any example but you can refer the following
https://www.researchgate.net/publica...FLUID_DYNAMICS https://dspace.mit.edu/handle/1721.1/38249
__________________
Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority. |
|
February 13, 2020, 11:03 |
|
#11 |
New Member
Karthikeyan
Join Date: Feb 2020
Posts: 6
Rep Power: 6 |
Yeah but this if for piping but i need something for a plate with many different composites layers.
|
|
February 13, 2020, 11:09 |
Thesis
|
#12 |
Senior Member
|
Look at the second one.
__________________
Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Running Ansys in BAtch Mode | kuleuvenstudent | ANSYS | 1 | October 18, 2017 12:11 |
[ANSYS Meshing] ANSYS mesh - I was surprised... | assafwei | ANSYS Meshing & Geometry | 0 | September 4, 2014 12:17 |
Ansys HPC licensing policy | assafwei | ANSYS | 0 | June 29, 2014 16:00 |
Using ICEM CFD to repair/edit ANSYS Meshing | Kaaji1359 | ANSYS | 2 | July 30, 2013 10:28 |
Exporting results from CFX to ANSYS ?? | sohail ahmed | CFX | 1 | December 20, 2007 01:10 |