Automatically writing of temperature profile?

beastmaster · January 20, 2021, 00:21

hello guys, i am trying to simulate flow across a heat sink, im using a parameter table for changing the geometry of the heat sink, i want to write out the temperature profile at the mid plane of the heat sink, is there any way to do this automatically, as far as i have searched, it can only be done manually, any help or guidance would be appreciated

Regards

AlexanderZ · January 20, 2021, 02:21

what do you mean under temperature profile?
you can make monitor and write data to file

what is you manual way to define temperature profile?

beastmaster · January 20, 2021, 02:28

Quote:

Originally Posted by AlexanderZ

what do you mean under temperature profile?
you can make monitor and write data to file

what is you manual way to define temperature profile?

Usually after the solving we manually go to cell zone condition and write profile, instead of that is there any way to write the profile of temperature automatically, like giving a command or something?

AlexanderZ · January 20, 2021, 03:08

Usually, It is possible to do using TUI commands, there are ways to execute these commands automatically as well

but to help you, you should describe the full way, you are defining that profile, which you are talking about

beastmaster · January 20, 2021, 03:17

Quote:

Originally Posted by AlexanderZ

Usually, It is possible to do using TUI commands, there are ways to execute these commands automatically as well

but to help you, you should describe the full way, you are defining that profile, which you are talking about

I am trying to do 500 simulations of flow across a heat sink, I am using parameter table for this, I want to write a temperature profile on a mid plans of the heat sink, is there any way to do it automatically like without opening fluent every time?

beastmaster · January 20, 2021, 06:27

Quote:

Originally Posted by AlexanderZ

Usually, It is possible to do using TUI commands, there are ways to execute these commands automatically as well

but to help you, you should describe the full way, you are defining that profile, which you are talking about

this is the write profile i was talking about, this had to be done manually right? i was asking if there is any way to do this process without opening fluent after every design point in my data table is solved

AlexanderZ · January 21, 2021, 01:25

you may make journal file with this code and execute it after each design point

Code:

(ti-menu-load-string (format #f "file write-profile test.pro plane-13 () total-temperature () " ))

beastmaster · January 21, 2021, 01:28

Quote:

Originally Posted by AlexanderZ

you may make journal file with this code and execute it after each design point

Code:

(ti-menu-load-string (format #f "file write-profile test.pro plane-13 () total-temperature () " ))

So after the code in journal file at the end I'll add this?

January 20, 2021, 00:21	Automatically writing of temperature profile?	#1
beastmaster New Member yadhu Join Date: Sep 2020 Posts: 17 Rep Power: 5	hello guys, i am trying to simulate flow across a heat sink, im using a parameter table for changing the geometry of the heat sink, i want to write out the temperature profile at the mid plane of the heat sink, is there any way to do this automatically, as far as i have searched, it can only be done manually, any help or guidance would be appreciated Regards

January 20, 2021, 02:21		#2
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	what do you mean under temperature profile? you can make monitor and write data to file what is you manual way to define temperature profile? __________________ best regards ****************************** press LIKE if this message was helpful

January 20, 2021, 03:08		#4
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	Usually, It is possible to do using TUI commands, there are ways to execute these commands automatically as well but to help you, you should describe the full way, you are defining that profile, which you are talking about __________________ best regards ****************************** press LIKE if this message was helpful

January 21, 2021, 01:25		#7
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	you may make journal file with this code and execute it after each design point Code: (ti-menu-load-string (format #f "file write-profile test.pro plane-13 () total-temperature () " )) __________________ best regards ****************************** press LIKE if this message was helpful

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] refineWallLayer Error	Yuby	OpenFOAM Meshing & Mesh Conversion	2	November 11, 2021 11:04
SU2 7.0.7 Built on CentOS 7, parallel computation pyscript mpi exit error?	EternalSeekerX	SU2	3	October 9, 2020 18:28
decomposePar problem: Cell 0contains face labels out of range	vaina74	OpenFOAM Pre-Processing	37	July 20, 2020 05:38
Temperature profile with isothermal steady state simulation	Procyon	CFX	6	November 11, 2019 12:06
Help please! UDF for Temperature profile in 3D	subhankar_bhandari	Fluent UDF and Scheme Programming	2	August 16, 2010 08:37