 |
 |
 |
|
|
|
[Sponsors] | ||||
December 22, 2005, 05:04
|
Help: Negative Volume
|
#1 |
|
Guest
Posts: n/a
|
I have constructed a model of the furnace. In this when i mesh one of the volume and then summarize the meshed volume then it shows that the meshed volume is negative volume. Please tell me the way to remove the negative volume.Does this negative volume has any effect when i export the model in Fluent and carry out the analysis over there. Thank you
|
|
|
||
|
December 22, 2005, 05:17
|
Re: Help: Negative Volume
|
#2 |
|
Guest
Posts: n/a
|
If you have a negative voulume, Fluent will diverge normally at the first iteration.
The only way to remove a negative volume is to remesh. |
|
|
|
||
|
December 22, 2005, 05:38
|
Re: Help: Negative Volume
|
#3 |
|
Guest
Posts: n/a
|
i have tried all type of the meshing in the negative volume but it doesnot disappear.. so i created virtual volume in the negative volume and meshed it. then negative volume disappeared. is this method correct?
|
|
|
|
||
|
December 22, 2005, 09:59
|
Re: Help: Negative Volume
|
#4 |
|
Guest
Posts: n/a
|
are u using symmetry? KP
|
|
|
|
||
|
December 22, 2005, 23:22
|
Re: Help: Negative Volume
|
#5 |
|
Guest
Posts: n/a
|
No i am not using symmtry.
|
|
|
|
||
|
December 23, 2005, 03:04
|
Re: Help: Negative Volume
|
#6 |
|
Guest
Posts: n/a
|
For myself, i change size parameter or something else before remeshing.
|
|
|
|
||
|
December 23, 2005, 04:08
|
Re: Help: Negative Volume
|
#7 |
|
Guest
Posts: n/a
|
I have change the size parameter but still I am getting the negative volume.
|
|
|
|
||
|
December 23, 2005, 04:13
|
Re: Help: Negative Volume
|
#8 |
|
Guest
Posts: n/a
|
Do you clean your cad geometry after import?
|
|
|
|
||
|
December 24, 2005, 04:59
|
Re: Help: Negative Volume
|
#9 |
|
Guest
Posts: n/a
|
Thanks atually i made the geomtry in Gambit it self. it is neccessary.
|
|
|
|
||
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| how to set periodic boundary conditions | Ganesh | FLUENT | 15 | November 18, 2020 06:09 |
| channelFoam for a 3D pipe | AlmostSurelyRob | OpenFOAM | 3 | June 24, 2011 13:06 |
| [blockMesh] BlockMesh FOAM warning | gaottino | OpenFOAM Meshing & Mesh Conversion | 7 | July 19, 2010 14:11 |
| On the damBreak4phaseFine cases | paean | OpenFOAM Running, Solving & CFD | 0 | November 14, 2008 21:14 |
| [blockMesh] Axisymmetrical mesh | Rasmus Gjesing (Gjesing) | OpenFOAM Meshing & Mesh Conversion | 10 | April 2, 2007 14:00 |
Linear Mode
