Error: pressure-far-field zone 1 has two adjacent

August 28, 2006, 03:20

Hi all ! I've just exported a mesh from gambit to fluent, and the grid check says i've got an "Error: pressure-far-field zone 1 has two adjacent cell zones." Does smbd knows the meaning of this ???

I'll be very thanksfull if somebody could help me very quick ;-) !

Many thanks !!

Kiril

August 28, 2006, 04:06

Probably it´s not a outside boundary? Perhaps it´s in the middle of the mesh (for that reason "has 2 adj cell zones")? Make sure it only has mesh on one side of the boundary.

Hope this helps!

Regards

August 28, 2006, 04:15

Yep !

In fact, I've added a face after having set the boundaries... and all the side of this face were outside the boundaries...

Thanks !

P.S : Plzz tell me if I was clear enough... I'm trying to improve my english... any remark is welcome !!

August 28, 2006, 04:27

I´m from Argentina so I´m working with my english too.. hehe, but I could understand you very well.

Take care.

August 28, 2006, 05:38

I'm from France... I'll be studying in England next year (starting in 2 weeks!)

Thanks !

Bybye

August 28, 2006, 03:20	Error: pressure-far-field zone 1 has two adjacent	#1
Kiril Guest Posts: n/a	Hi all ! I've just exported a mesh from gambit to fluent, and the grid check says i've got an "Error: pressure-far-field zone 1 has two adjacent cell zones." Does smbd knows the meaning of this ??? I'll be very thanksfull if somebody could help me very quick ;-) ! Many thanks !! Kiril

August 28, 2006, 04:06	Re: Error: pressure-far-field zone 1 has two adjac	#2
HSeldon Guest Posts: n/a	Probably it´s not a outside boundary? Perhaps it´s in the middle of the mesh (for that reason "has 2 adj cell zones")? Make sure it only has mesh on one side of the boundary. Hope this helps! Regards

August 28, 2006, 04:15	Re: Error: pressure-far-field zone 1 has two adjac	#3
Kiril Guest Posts: n/a	Yep ! In fact, I've added a face after having set the boundaries... and all the side of this face were outside the boundaries... Thanks ! P.S : Plzz tell me if I was clear enough... I'm trying to improve my english... any remark is welcome !!

August 28, 2006, 04:27	Re: Error: pressure-far-field zone 1 has two adjac	#4
HSeldon Guest Posts: n/a	I´m from Argentina so I´m working with my english too.. hehe, but I could understand you very well. Take care.

August 28, 2006, 05:38	Re: Error: pressure-far-field zone 1 has two adjac	#5
Kiril Guest Posts: n/a	I'm from France... I'll be studying in England next year (starting in 2 weeks!) Thanks ! Bybye

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cht tutorial in 15	braennstroem	OpenFOAM Running, Solving & CFD	197	June 10, 2015 03:02
Moving mesh	Niklas Wikstrom (Wikstrom)	OpenFOAM Running, Solving & CFD	122	June 15, 2014 06:20
Problem in running ICEM grid in Openfoam	Tarak	OpenFOAM	6	September 9, 2011 17:51
Problem in IMPORT of ICEM input file in FLUENT	csvirume	FLUENT	2	September 9, 2009 01:08
Problem with rhoSimpleFoam	matteo_gautero	OpenFOAM Running, Solving & CFD	0	February 28, 2008 06:51