|
[Sponsors] |
October 8, 2006, 20:20 |
How to use LES
|
#1 |
Guest
Posts: n/a
|
I get some materials which show some cases using LES, but when i do it ,i find that i cannt use LES for 2D problems.Dear friends, please give some advices how to solve 2D problems using LES by FLUENT software?
|
|
October 11, 2006, 13:29 |
Re: How to use LES
|
#2 |
Guest
Posts: n/a
|
see the previous posts, there are some discussions on this topic
|
|
October 11, 2006, 17:16 |
Re: How to use LES
|
#3 |
Guest
Posts: n/a
|
there is a way to activate 2d les, i have forgotten the command and unable to find it.
|
|
October 11, 2006, 17:32 |
activate LES 2D
|
#4 |
Guest
Posts: n/a
|
This is how you can activate 2d les, (on command prompt)
(rpsetvar 'les-2d? #t) |
|
October 11, 2006, 21:06 |
Re: activate LES 2D
|
#5 |
Guest
Posts: n/a
|
I have the same question.you say use (rpsetvar 'les-2d? #t) , I hade down, but it can run.The console present " invalid command [rpsetvar]" sorry ,I'm chinese, my english ability is poor.
|
|
October 12, 2006, 00:26 |
Re: activate LES 2D
|
#6 |
Guest
Posts: n/a
|
dear zxaar, Thank you for your answer. I try it again .It do can run. Now I can run les-2d.
|
|
October 12, 2006, 03:37 |
Re: How to use LES
|
#7 |
Guest
Posts: n/a
|
dear friend Im interesting in simulation of Aero-Acoustics noise using LES turbulent model. If you have any tutorials related to this topic please send it to me
|
|
October 12, 2006, 20:34 |
Re: How to use LES
|
#8 |
Guest
Posts: n/a
|
Dear Friend you are really in bad luck, because how to enable 2d les i could find out from a 'Aero-Acoustics noise using LES ' tutorial. And due to hard disk crash I lost all the data relevant to fluent tutorials and other docs. So i can not mail you that. But if you try to search the fluent tutorials of version 6.18 or before you might get that tutorial. More than this I am afraid I can not do.
|
|
October 15, 2006, 12:13 |
Re: How to use LES
|
#9 |
Guest
Posts: n/a
|
dear zxaar thanks for replay i will try search the internet
|
|
October 16, 2006, 05:34 |
Re: activate LES 2D
|
#10 |
Guest
Posts: n/a
|
Dear Friends,Could tell me how to run in detail? I tried but failed. i don't know how to run (in FLUENT 6) Really. thx!!
|
|
October 16, 2006, 06:14 |
Re: activate LES 2D
|
#11 |
Guest
Posts: n/a
|
its easy: start fluent 2d
go to command prompt of fluent and type letter by letter (exactly with () ): (rpsetvar 'les-2d? #t) it should work, i have done it many times. |
|
October 16, 2006, 18:29 |
Re: activate LES 2D
|
#12 |
Guest
Posts: n/a
|
Thank you very much!!it works!!so can you tell me why it happens or what else can happen by the way?
|
|
October 16, 2006, 19:54 |
Re: activate LES 2D
|
#13 |
Guest
Posts: n/a
|
we did not do nothing much:
look at the command (rpsetvar 'les-2d? #t) rpsetvar is scheme command for setting a value of a variable, we set the value of variable les-2d to t or true. or in other words we enable the les-2d, using the command in () is syntax of fluent. By the same way you can enable lot of things, if you want to explore it, there is a way to do it, take a very small mesh , may be 100 cells odd, setup a case and save the case as ascii from fluent. open that case file on word pad, you can figure out lot of such variables doing lot of stuff. try it, i learnt a lot from it |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Turbulence dampening due to magnetic field in LES and RAS | eelcovv | OpenFOAM | 0 | June 8, 2010 11:35 |
LES grid mesh | L3munoz | Main CFD Forum | 0 | April 7, 2010 05:05 |
LES and combustion model | Margherita Cadorin | CFX | 0 | October 29, 2008 05:24 |
Differences between a laminar code and a les one | ben | Main CFD Forum | 9 | February 16, 2005 23:40 |
Some Questions about LES. | Bin Li | Main CFD Forum | 2 | February 20, 2004 09:58 |