CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > FLUENT

error in polyflow while inverse extruding

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   July 15, 2008, 00:01
Default error in polyflow while inverse extruding
  #1
shyam chunduru
Guest
 
Posts: n/a
hello

i am shyam ,i had been trying to simulate inverse extrusion in the polyflow software.

i need to use Carreau-Yasuda law.

i am just trying with rectangle block of 0.02m,0.002m i had done with constant viscosity and had got the results. but i was unable to do this with varying viscosity and temperatures.

the following is the error i am getting.

["

***************************

* Expert tool diagnostics *

***************************

Out of convergence disk

***************************

* Expert tool diagnostics *

***************************

The problem F.E.M. Task 1 has not converged.

***************************

* Expert tool Suggestions *

***************************

There is a non-linearity in problem Inflow introduced by the power

law index (n) of the viscosity law. The value of the power law index

is 0.32.

The expert system suggests to use a Picard iterative scheme with a

number of iterations about 30 or 40.

There is a non-linearity in problem Navier-Stokes 3D introduced by

the power law index (n) of the viscosity law. The value of the power

law index is 0.32.

The expert system suggests to use a Picard iterative scheme with a

number of iterations about 30 or 40.

There is a non-linearity in problem Navier-Stokes 3D introduced by

the power law index (n) of the viscosity law. The value of the power

law index is 0.32.

The expert system suggests to use an evolution for this parameter

coupling with Newton-Raphson iterative scheme. The evolution scheme

must be the following :

- f(s) = 1/s

- S-ini = n = 0.32

- S-final = 1.0

- Initial increment = 0.4 = n/0.8.

If you can not define the evolution with those typical values of the

evolution parameters, maybe your problem is not well defined. Please

check the setup of your simulations.

************************************************** ********

* Expert tool advice in order to optimize the simulation *

************************************************** ********

At least one bad element has been detected in the mesh.

The worst has the following feature(s)

Negative Jacobian in element 3150, (x,y,z) = (0.0023884, 0.0009407,

0.06459).

Too small angle in element 2130, (x,y,z) = (0.0022212, 0.0009455,

0.04797).

Too big angle in element 2219, (x,y,z) = (0.0022555, 0.0009965,

0.04307).

Non-convex element 26, (x,y,z) = (0.019045, 0.0010259, 0.07519).

This can lead to local inaccuracies and possibly convergence

difficulties. It is strongly recommended to fix the mesh.

"]

In order to solve this i had tried by changing the mesh. some times second sugestion doesnt appear.

can any one give me sugestions to solve this problem.

thanking you

shyam

  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
polyflow error duton FLUENT 2 June 21, 2021 06:47
[Polyflow] Slicing error Jason FLUENT 0 April 8, 2007 11:35
Polyflow memory error markus FLUENT 0 September 13, 2006 04:20
fatal error in polyflow Robert FLUENT 0 March 10, 2003 21:01
Error message in Polyflow M. Tabaddor FLUENT 1 February 15, 2002 14:49


All times are GMT -4. The time now is 15:18.