Simplified VOF Model

gulbenkian · June 10, 2010, 15:57

Hello

I am trying to solve a transient simplified model in 2D. Air is flowing from a source at 200000 Pa and get into contact with a pool of water of 2mm X 4mm before expands to atmospheric conditions see Figure 1.

I want to see the deformation of the water (droplet formation if any) due to the air flow. I am having problems to get convergence in the model. I am using a VOF model using air as primary phase and the water as secondary phase. As boundary conditions I am using a pressure inlet and pressure oulet conditions. I am patching the water at the beginning. I have used a k-e model and a simplified laminar model for the air and a time step size of 0.0001, however, after I begin the iterative process, it quickly diverge.

I highly appreciate if someone can give me some ideas.

Thanks in advance

pranab_jha · June 10, 2010, 16:52

Hi,
What error message does Fluent give you?
I am also using VOF and facing some issues with divergence. I am modeling two-phase flow in pipe. I got the error msg: "divergence detected in AMG solver: pressure correction" when I initialized the whole pipe domain with VF =1 or even with VF = 0.5. But for low phase velocities, I was able to 'avoid' divergence by lowering the relaxation factors for pressure from 1 to 0.5. But I am not able to get around it for higher velocities (air and water ~ 1.5 m/s, pipe dia = 50 mm) by lowering the value further.
I guess you can try it. Maybe it works for you. If you come across any useful tip, do let me know.
Thanks,
Pranab

June 10, 2010, 15:57	Simplified VOF Model	#1
gulbenkian New Member Join Date: Jun 2010 Posts: 2 Rep Power: 0	Hello I am trying to solve a transient simplified model in 2D. Air is flowing from a source at 200000 Pa and get into contact with a pool of water of 2mm X 4mm before expands to atmospheric conditions see Figure 1. I want to see the deformation of the water (droplet formation if any) due to the air flow. I am having problems to get convergence in the model. I am using a VOF model using air as primary phase and the water as secondary phase. As boundary conditions I am using a pressure inlet and pressure oulet conditions. I am patching the water at the beginning. I have used a k-e model and a simplified laminar model for the air and a time step size of 0.0001, however, after I begin the iterative process, it quickly diverge. I highly appreciate if someone can give me some ideas. Thanks in advance

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Doubts UDS Flux, UDS Unsteady for VOF model	kel85uk	FLUENT	0	March 17, 2010 08:53
VOF Model or Mixture Model	mems21	FLUENT	2	March 9, 2010 10:37
A Problem with setting the time step in VOF model	Le	FLUENT	2	July 20, 2006 22:00
free surface of VOF and melting model?	wanghong	FLUENT	3	March 13, 2006 09:57
help needed for vof model	yan	FLUENT	3	December 16, 2005 01:17

June 10, 2010, 16:52		#2
pranab_jha Member Pranab N Jha Join Date: Nov 2009 Location: Houston, TX Posts: 86 Rep Power: 16	Hi, What error message does Fluent give you? I am also using VOF and facing some issues with divergence. I am modeling two-phase flow in pipe. I got the error msg: "divergence detected in AMG solver: pressure correction" when I initialized the whole pipe domain with VF =1 or even with VF = 0.5. But for low phase velocities, I was able to 'avoid' divergence by lowering the relaxation factors for pressure from 1 to 0.5. But I am not able to get around it for higher velocities (air and water ~ 1.5 m/s, pipe dia = 50 mm) by lowering the value further. I guess you can try it. Maybe it works for you. If you come across any useful tip, do let me know. Thanks, Pranab