ansys icem to fluent help?

mymach · June 28, 2010, 17:38

hi...
how ı can output a ansys icem mesh to fluent.ı dont know,how ı must do boundry conditions.
ıt about water fluıd in a pipe.

Piotrek · June 29, 2010, 02:22

Hi,

You should go to Output in ICEM and choose Fluent. Than you can specify your boundry conditions. Wither way, all BC can be changed, and most likely will be, in Fluent.
Type of fluid is specified in the solver.

mymach · July 1, 2010, 04:53

ı tryed but ı cant open at fluent.ıt gives error message..

> Reading "C:\Documents and Settings\m\Desktop\projeckt documents\boru\fluent.msh"...
405 nodes.
432 mixed cells, zone 15.
Error: read: face 1034, zone 16.
Reading Faces: failed while reading section 13.
Clearing partially read grid.

Error: Read aborted due to critical error.
Error Object: ()

Error: Error reading "C:\Documents and Settings\m\Desktop\projeckt documents\boru\fluent.msh".
Error Object: #f

Dr.been · July 3, 2010, 07:58

Quote:

Originally Posted by mymach

hi...
how ı can output a ansys icem mesh to fluent.ı dont know,how ı must do boundry conditions.
ıt about water fluıd in a pipe.

In case of Haxa mesh , are you sure that all blocks were associated with geometry's part ?

After choose output (ansys , fluent_v6) and set BCs, please notice when you write this input the program warn a complete message or not ?

hope this help

mymach · July 3, 2010, 16:56

all bloks were associated...ıt still gives error mesage....

mymach · July 7, 2010, 07:41

i tryed to open with fluent but it gives an error message
error: there no cell zone available
please read a valid volume mesh

i dont understan where i made a mistake...
i made mesh with blok i think mesh is volume mesh....
help

Piotrek · July 7, 2010, 08:21

I understand your mesh is 3d. If that is the case are you sure you specified "body" inside your geometry?

mymach · July 7, 2010, 08:28

yes there is body inside the geometry but i m not sure that is ok i just pick the geometrys different side and body is exist.

June 28, 2010, 17:38	ansys icem to fluent help?	#1
mymach New Member yildirim Join Date: May 2010 Location: germany Posts: 6 Rep Power: 15	hi... how ı can output a ansys icem mesh to fluent.ı dont know,how ı must do boundry conditions. ıt about water fluıd in a pipe.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
drag coefficient in ansys fluent 12.0	krishna	FLUENT	19	April 12, 2018 00:49
How to open Icem mesh in Ansys Fluent?	emmkell	FLUENT	27	February 6, 2018 03:34
[GAMBIT] 3.5 years overtake by Ansys: Where are the enhancements in grid generation	Volker P.	ANSYS Meshing & Geometry	22	January 17, 2012 17:27
FLUENT results to ANSYS	Jin Yan	FLUENT	2	April 28, 2011 11:22
Exporting ICEM Tetra Grid to Fluent with Hexa-Core	Tim	FLUENT	2	August 30, 2007 07:16

June 29, 2010, 02:22		#2
Piotrek New Member Join Date: Jun 2009 Posts: 15 Rep Power: 16	Hi, You should go to Output in ICEM and choose Fluent. Than you can specify your boundry conditions. Wither way, all BC can be changed, and most likely will be, in Fluent. Type of fluid is specified in the solver.

July 1, 2010, 04:53		#3
mymach New Member yildirim Join Date: May 2010 Location: germany Posts: 6 Rep Power: 15	ı tryed but ı cant open at fluent.ıt gives error message.. > Reading "C:\Documents and Settings\m\Desktop\projeckt documents\boru\fluent.msh"... 405 nodes. 432 mixed cells, zone 15. Error: read: face 1034, zone 16. Reading Faces: failed while reading section 13. Clearing partially read grid. Error: Read aborted due to critical error. Error Object: () Error: Error reading "C:\Documents and Settings\m\Desktop\projeckt documents\boru\fluent.msh". Error Object: #f

July 3, 2010, 16:56		#5
mymach New Member yildirim Join Date: May 2010 Location: germany Posts: 6 Rep Power: 15	all bloks were associated...ıt still gives error mesage....

July 7, 2010, 07:41		#6
mymach New Member yildirim Join Date: May 2010 Location: germany Posts: 6 Rep Power: 15	i tryed to open with fluent but it gives an error message error: there no cell zone available please read a valid volume mesh i dont understan where i made a mistake... i made mesh with blok i think mesh is volume mesh.... help

July 7, 2010, 08:21		#7
Piotrek New Member Join Date: Jun 2009 Posts: 15 Rep Power: 16	I understand your mesh is 3d. If that is the case are you sure you specified "body" inside your geometry?

July 7, 2010, 08:28		#8
mymach New Member yildirim Join Date: May 2010 Location: germany Posts: 6 Rep Power: 15	yes there is body inside the geometry but i m not sure that is ok i just pick the geometrys different side and body is exist.