|
[Sponsors] |
July 25, 2010, 00:54 |
jet pum
|
#1 |
New Member
aime marthial
Join Date: Mar 2010
Posts: 14
Rep Power: 16 |
hi everyone
does someone have any idea how to modeling high velocity flow in ejector( as the one use in refrigeration cycle) but in my present case the fluid is water-vapor ,the primary flow has velocity in order of 200m/s at 100C of temperature and the secondary flow has a pressure in order 6000Pa and temperature of 45C the represent view of the ejector is given with this linkhttp://ijlct.oxfordjournals.org/cgi/...4/1/2/CTN001F2 i already try what i can but i don' have any good result, if someone have any tutorial or any ideas which can help me i will be glad thank to take your time to read me |
|
July 31, 2010, 06:45 |
|
#2 |
New Member
Tomek
Join Date: Jul 2010
Posts: 5
Rep Power: 15 |
I simulated very similar model. It was lowpressure ejector of domestic burners. I have two streams of gas: natural gas and air (primary air). I used model: species transport. Thanks for this model i get density which value was consequence of mixing of this two streams. So this model was kind of ejector because velocity of gas (about 80 m/s) make that the air was suck in to burners. Sorry for my english. It is polish-english
|
|
July 31, 2010, 07:38 |
|
#3 |
New Member
aime marthial
Join Date: Mar 2010
Posts: 14
Rep Power: 16 |
thank Tomek to take your time replying me ,my English is not good too so
in your work you used two different fluid that it?how low was pressure you used? because i realized that the high pressure i use maybe the real problem.. |
|
July 31, 2010, 11:47 |
|
#4 |
New Member
Tomek
Join Date: Jul 2010
Posts: 5
Rep Power: 15 |
I used one phase (gas phase). One gas it was natural gas, second gas was air - I simulated how domestic burner work. The pressure of natural gas was 2000 Pa (pressure above atmospheric), the pressure of air was O Pa (my boundary conditions). If you choose model 2D try to use model 3D. When I use model 2D the result was far-away from correct answer.
|
|
July 31, 2010, 11:53 |
|
#5 |
New Member
Tomek
Join Date: Jul 2010
Posts: 5
Rep Power: 15 |
I think the level of pressure is not problem. It's depend on size your diameter. I used the nozzle with diameter 1,07 [mm], the gauge pressure 2000 Pa caused max speed flow about 80 m/s in the nozzle.
|
|
August 3, 2010, 10:09 |
|
#6 |
New Member
aime marthial
Join Date: Mar 2010
Posts: 14
Rep Power: 16 |
thank u for your indications and sorry to reply little late i have been busy with others stuff
i will then first try to use a 3D model and see if i get better result, i work with a diameter of 2.4mm , i will let u know what i get, thank you again for your time |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Jet fan and Tunnel simulation | ahlo7 | CFX | 9 | November 13, 2019 04:54 |
2D Plane Jet Fluent Solution | doug | Main CFD Forum | 11 | February 4, 2019 09:34 |
determination of jet front | Fred | CFX | 5 | February 11, 2007 12:01 |
method to determine jet front | Fred | Main CFD Forum | 0 | February 8, 2007 13:15 |
IMPINGING JET ........... HELP!!!!!!!! | Amir Omoumi | Main CFD Forum | 10 | August 30, 1999 22:11 |