Tutorial Phase separation FLUENT (HELP)

sincity · July 18, 2011, 21:01

i need some tutorial about phase separation (multiphase fluid) from FLUENT thanks.

sincity · July 19, 2011, 22:16

dear mr. sadeghi
let me introduce myself, i'm undergraduate student in one of indonesian university my major is mechanical eng. my final task is about modelling gravity separator which use three phase of fluid (gas-oil-water) i'm using FLUENT as my CFD code...i want to ask some question about modeling three phase in FLUENT, would you help me??

eng_s_sadeghi · July 19, 2011, 22:38

ok.
for fluid seperation, you should use vof 3phase model. also you should enable gravity.
they will seperate by time, after initial condition. the point is that you should use unsteady solution to could converge.

sincity · July 19, 2011, 22:44

using VOF for my model of my three phase simulation....should i add UDF for that, or not???because i read in FLUENT user guide that if i have more than one secondary phase i should adding some UDF called phase domain index???...would you explain it to me?? i'm very confusing should i use UDF or not for the three phase simulation

eng_s_sadeghi · July 20, 2011, 00:47

There is no need to UDF in this step.
you should just enable 3phases and run as an initial solution.
then you can add more details such as drag, lift, surface tension between phases, etc.

sincity · July 20, 2011, 01:16

i've tried in so many ways doing the simulation but why i didn't have my interface correctly.
here is my set up, i use VOF multiphase model

fluid: gas--->primary
oil ---->secondary
water--->secondary

boundary condition: inlet--->mass flow inlet
outlet--->outflow

implicit VOF scheme

gravity enabled

k-epsilon standard wall function

specified operating density enabled, PISO,PRESTO, Unsteady state

so i beg for you mr. sadeghi if you have been doing some multiphase flow like this you could give me an assistance or maybe you didn't but you have colleague who was an expert in gas-oil-water separator maybe you could connect me to him/her. thanks mr. sadeghi. (i almost did this for two years and no results)

sincity · July 20, 2011, 03:25

i just need your guidance if you mind, i'll do it by myself. mr.sadeghi do you have a colleague that expert in this topic??

July 18, 2011, 21:01	Tutorial Phase separation FLUENT (HELP)	#1
sincity Member wibi ario Join Date: Feb 2011 Posts: 46 Rep Power: 15	i need some tutorial about phase separation (multiphase fluid) from FLUENT thanks.

July 19, 2011, 22:38		#3
eng_s_sadeghi Member Join Date: Mar 2011 Posts: 64 Rep Power: 15	ok. for fluid seperation, you should use vof 3phase model. also you should enable gravity. they will seperate by time, after initial condition. the point is that you should use unsteady solution to could converge. __________________ Saeed Sadeghi Ansys Fluent CFD Consultant

July 20, 2011, 00:47		#5
eng_s_sadeghi Member Join Date: Mar 2011 Posts: 64 Rep Power: 15	There is no need to UDF in this step. you should just enable 3phases and run as an initial solution. then you can add more details such as drag, lift, surface tension between phases, etc. __________________ Saeed Sadeghi Ansys Fluent CFD Consultant

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
store separation tutorial	haider	FLUENT	2	June 29, 2014 08:53
Fluent SI engine tutorial problem	Jonny6001	FLUENT	4	January 22, 2012 19:26
How to find the separation point in fluent	caohan	FLUENT	3	April 8, 2010 13:48
Does anyone has the case & dat file for tutorial of ansys fluent 12	zhang.limin	Main CFD Forum	0	March 2, 2010 13:03
Request for pipe bifurcation fluent tutorial case	Giorgos Momferratos	FLUENT	0	October 20, 2008 15:10

July 19, 2011, 22:16		#2
sincity Member wibi ario Join Date: Feb 2011 Posts: 46 Rep Power: 15	dear mr. sadeghi let me introduce myself, i'm undergraduate student in one of indonesian university my major is mechanical eng. my final task is about modelling gravity separator which use three phase of fluid (gas-oil-water) i'm using FLUENT as my CFD code...i want to ask some question about modeling three phase in FLUENT, would you help me??

July 19, 2011, 22:44		#4
sincity Member wibi ario Join Date: Feb 2011 Posts: 46 Rep Power: 15	using VOF for my model of my three phase simulation....should i add UDF for that, or not???because i read in FLUENT user guide that if i have more than one secondary phase i should adding some UDF called phase domain index???...would you explain it to me?? i'm very confusing should i use UDF or not for the three phase simulation

July 20, 2011, 01:16		#6
sincity Member wibi ario Join Date: Feb 2011 Posts: 46 Rep Power: 15	i've tried in so many ways doing the simulation but why i didn't have my interface correctly. here is my set up, i use VOF multiphase model fluid: gas--->primary oil ---->secondary water--->secondary boundary condition: inlet--->mass flow inlet outlet--->outflow implicit VOF scheme gravity enabled k-epsilon standard wall function specified operating density enabled, PISO,PRESTO, Unsteady state so i beg for you mr. sadeghi if you have been doing some multiphase flow like this you could give me an assistance or maybe you didn't but you have colleague who was an expert in gas-oil-water separator maybe you could connect me to him/her. thanks mr. sadeghi. (i almost did this for two years and no results)

July 20, 2011, 03:25		#7
sincity Member wibi ario Join Date: Feb 2011 Posts: 46 Rep Power: 15	i just need your guidance if you mind, i'll do it by myself. mr.sadeghi do you have a colleague that expert in this topic??