Creating a axi-symmetric mesh for OpenFOAM

AnthonyP · November 8, 2018, 18:12

Hi,

I am trying to create an axi-symmetric mesh for my project. I am using GridPro because I greatly appreciate the high-quality multiblock structured meshing. Unfortuneately, I am running into some issues using OpenFOAM tools to convert the the 3d mesh from gridPro to the single cell thick wedge style mesh that OpenFOAM uses for axisymmetric cases.

My question:

Is it possible to directly generate such a grid with just GridPro without needed to use openFOAM tools to make the axisymmetric conversion?

LuckyTran · December 18, 2018, 07:54

GridPro won't let you do a single cell thick mesh (least 2) so it would have to be in 2D grid. Not sure if it would be doable at all using either method. That is, I'm not sure there is an OpenFOAM tool that converts a 2D mesh into a wedge (but step 5 looks promising). And GridPro can't wedge it on its own.

AnthonyP · December 27, 2018, 12:51

Thank you for your help; I'll avoid the direct route then.

As a note: I found the error during my conversion process. So it is perfectly doable to convert a 2D planar mesh generated by GridPro to an axi-symmetric mesh for openFOAM using its extrudeMesh utility.
Just be careful of the points near the to-be axis and ensure they do not cross it before running the utility (Crossing the axis even if by 1pt many orders smaller than the mesh...can cause inverted cells)

November 8, 2018, 18:12	Creating a axi-symmetric mesh for OpenFOAM	#1
AnthonyP New Member Tony Join Date: May 2016 Posts: 22 Rep Power: 9	Hi, I am trying to create an axi-symmetric mesh for my project. I am using GridPro because I greatly appreciate the high-quality multiblock structured meshing. Unfortuneately, I am running into some issues using OpenFOAM tools to convert the the 3d mesh from gridPro to the single cell thick wedge style mesh that OpenFOAM uses for axisymmetric cases. My question: Is it possible to directly generate such a grid with just GridPro without needed to use openFOAM tools to make the axisymmetric conversion?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] Add Mesh Layers doesnt work on the whole surface	Kryo	OpenFOAM Meshing & Mesh Conversion	13	February 17, 2022 07:34
[snappyHexMesh] SnappyHexMesh for internal Flow	vishwa	OpenFOAM Meshing & Mesh Conversion	24	June 27, 2016 08:54
Creating Volume mesh from surface mesh	Vivek.oswal	Mesh Generation & Pre-Processing	0	August 7, 2015 14:11
Possible Bug in pimpleFoam (or createPatch) (or fluent3DMeshToFoam)	cfdonline2mohsen	OpenFOAM	3	October 21, 2013 09:28
[ICEM] Generating Mesh for STL Car in Windtunnel Simulation	tommymoose	ANSYS Meshing & Geometry	48	April 15, 2013 04:24

December 18, 2018, 07:54		#2
LuckyTran Senior Member Lucky Join Date: Apr 2011 Location: Orlando, FL USA Posts: 5,674 Rep Power: 65	GridPro won't let you do a single cell thick mesh (least 2) so it would have to be in 2D grid. Not sure if it would be doable at all using either method. That is, I'm not sure there is an OpenFOAM tool that converts a 2D mesh into a wedge (but step 5 looks promising). And GridPro can't wedge it on its own.

December 27, 2018, 12:51		#3
AnthonyP New Member Tony Join Date: May 2016 Posts: 22 Rep Power: 9	Thank you for your help; I'll avoid the direct route then. As a note: I found the error during my conversion process. So it is perfectly doable to convert a 2D planar mesh generated by GridPro to an axi-symmetric mesh for openFOAM using its extrudeMesh utility. Just be careful of the points near the to-be axis and ensure they do not cross it before running the utility (Crossing the axis even if by 1pt many orders smaller than the mesh...can cause inverted cells)