 |
 |
 |
|
|
|
[Sponsors] | ||||
the static pressure at one outlet is negative? |
 |
|
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
August 15, 2013, 03:04
|
the static pressure at one outlet is negative?
|
#1 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13  |
Hi, my friends, I simulated the pressure distribution in a geometry with pushed air in it. But I got a negative pressure at one outlet. That means the static pressure at this outlet is lower than the static pressure at reference point (101325 Pa). But I guess the pressure at this outlet should be higher than 101325. Because air is pushed from the bottom to the top of the geometry. Maybe the inlet is too close to the outlet. Then I extended the outlet to 5 times of the distance from the original position. And the static pressure are positive .But the mass flow rate at this outlet is positive， which is different with other two outlets.
My questions are: 1. why is the mass flow rate is positive at this outlet? 2. Is the pressure at the original outlet reliable after I extended it to a far distance? I am so forwarding to your help! Thanks so so much! Regards, Rong The original geometry is like this: Attachment 24418 |
|
|
|
|
|
August 15, 2013, 03:06
|
|
#2 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
the original geometry
|
|
|
|
|
|
|
August 15, 2013, 03:07
|
|
#3 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
the static pressure at inlet and outlets
|
|
|
|
|
|
|
August 15, 2013, 03:09
|
|
#4 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
the geometry after extended outlets
|
|
|
|
|
|
|
August 15, 2013, 03:12
|
|
#5 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
the mass flow rate at inlets and outlets after extended the outlets
|
|
|
|
|
|
|
August 15, 2013, 03:14
|
|
#6 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
the static pressure at inlets and outlets after extended outlets
|
|
|
|
|
|
|
August 15, 2013, 03:15
|
|
#7 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
the mass flow rate at inlets and outlets in the original geometry
|
|
|
|
|
|
|
August 15, 2013, 21:01
|
|
#8 |
|
Member
Rong Yue
Join Date: Oct 2012
Location: Canada
Posts: 65
Rep Power: 13 |
Does anybody understand my problem? Please! Thanks a lot!
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Pressure Driven Supersonic Flow in Converging-Diverging Nozzle | cdm | OpenFOAM Running, Solving & CFD | 7 | August 28, 2019 01:37 |
| Modeling transient negative pressure (suction pressure) in outlet | N_mrtz | FLUENT | 1 | July 18, 2013 20:59 |
| Question Concerning Pressure Value (Pressure outlet) and Reference Pressure (Physics) | andy_flow | STAR-CCM+ | 1 | July 9, 2013 08:44 |
| [blockMesh] BlockMesh FOAM warning | gaottino | OpenFOAM Meshing & Mesh Conversion | 7 | July 19, 2010 14:11 |
| what the result is negatif pressure at inlet | chong chee nan | FLUENT | 0 | December 29, 2001 05:13 |
Linear Mode
