CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Vehicle Aerodynamics

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   November 8, 2013, 16:58
Default Vehicle Aerodynamics
  #1
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Hello all,
I have recently started working with CFD softwares and have a question. I'll be simulating a car and analysing the drag co-efficient and the downforce.

I believe there are two approaches for this simulation

1) Keep the car and the road at rest and give inlet velocity equal to the velocity of the car

or

2) Directly give the car it's velocity without creating a velocity inlet.

I wanted to ask you if the values of drag and downforce would be different for these two approaches ? Or would they be same?
Also, if I want to give the velocity to the car itself, how can I give it, in Fluent ?

Thanks !

Last edited by Harshal; November 10, 2013 at 08:15.
Harshal is offline   Reply With Quote

Old   November 9, 2013, 14:18
Default
  #2
New Member
 
Ahmad jibreel
Join Date: Oct 2013
Posts: 6
Rep Power: 12
jibreel is on a distinguished road
i think results will be same.
jibreel is offline   Reply With Quote

Old   November 10, 2013, 13:39
Default
  #3
Senior Member
 
plucas's Avatar
 
Anonymous
Join Date: Dec 2011
Location: USA
Posts: 108
Rep Power: 14
plucas is on a distinguished road
You do not want to keep the road at rest unless you are comparing results to a non-rolling road windtunnel.
plucas is offline   Reply With Quote

Old   November 10, 2013, 13:44
Default the road isn't stationary relative to the car
  #4
New Member
 
Join Date: May 2013
Posts: 12
Rep Power: 12
levivad is on a distinguished road
the road actually moves at the same speed as the air (if the car is assumed stationary).
this would cause a difference in results between a moving car, stationary road+air simulation and a stationary car+road, moving air simulation.
I would suggest simulating the road as a moving wall.
levivad is offline   Reply With Quote

Old   November 10, 2013, 21:24
Default
  #5
Senior Member
 
truffaldino's Avatar
 
Join Date: Jan 2011
Posts: 249
Blog Entries: 5
Rep Power: 17
truffaldino is on a distinguished road
I am not sure, but I think results will be only slightly different for moving and stationary road, since, rougly speaking, the size of road bl is much less than the distance between road and a car.
truffaldino is offline   Reply With Quote

Old   November 16, 2013, 18:07
Default
  #6
Member
 
Shenren Xu
Join Date: Jan 2011
Location: London, U.K.
Posts: 67
Rep Power: 15
Shenren_CN is on a distinguished road
So are you implying that the distance between road and a car is negative? :-)

Quote:
Originally Posted by truffaldino View Post
I am not sure, but I think results will be only slightly different for moving and stationary road, since, rougly speaking, the size of road bl is much less than the distance between road and a car.
Shenren_CN is offline   Reply With Quote

Old   November 17, 2013, 04:42
Default
  #7
Member
 
Mohsen
Join Date: Jul 2012
Posts: 49
Rep Power: 13
smhosseini is on a distinguished road
In fluent, you can consider the stationary air at time zero and you should consider moving wall boundary condition for external wall of your car. You should mesh the outside part of your car that you guess there is boundary layer, the part of air around the car that is influenced by car moving.
Be successful.
smhosseini is offline   Reply With Quote

Old   November 17, 2013, 06:35
Default
  #8
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Quote:
Originally Posted by smhosseini View Post
In fluent, you can consider the stationary air at time zero and you should consider moving wall boundary condition for external wall of your car. You should mesh the outside part of your car that you guess there is boundary layer, the part of air around the car that is influenced by car moving.
Be successful.
Hello smhosseini,

thanks for your reply. Unfortunately, I'm a bit confused. You mentioned that I should consider air as stationary at time zero.
Can you please explain this point ?
Do you mean that I should do a transient simulation ?
I thought that for this case, a time steady simulation would work.

Thanks, again,

Harshal
Harshal is offline   Reply With Quote

Old   November 17, 2013, 09:14
Default
  #9
Member
 
Mohsen
Join Date: Jul 2012
Posts: 49
Rep Power: 13
smhosseini is on a distinguished road
I'm sorry because I didn't explain completely.
You can solve this problem steady or unsteady. I mean you don't need any inlet or outlet flow. you can start iteration with stationary air for steady state solution. If you need the variation of boundary layer with time, you can solve unsteady problem.
smhosseini is offline   Reply With Quote

Old   November 17, 2013, 17:20
Default
  #10
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Quote:
Originally Posted by smhosseini View Post
I'm sorry because I didn't explain completely.
You can solve this problem steady or unsteady. I mean you don't need any inlet or outlet flow. you can start iteration with stationary air for steady state solution. If you need the variation of boundary layer with time, you can solve unsteady problem.
Hello smhosseini,
thank you for your reply. I plan to do a time steady state simulation. In fact, I have several doubts regarding the setting in Fluent and have posted the same in the Fluent forum. Would you be so kind to view my post and to answer it ? I have posted the link below. It would be really helpful, if you could answer or suggest some solutions for my doubts.

http://www.cfd-online.com/Forums/flu...downforce.html

Thank You,
Regards,

Harshal
Harshal is offline   Reply With Quote

Old   April 10, 2014, 10:07
Default Simultaneous simulations for different speeds
  #11
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Hello all,
I need your help. I have to find out the Cd and Cl values for a car using k-epsilon and k-omega models for multiple speeds (about 15 different speeds). Can some one please tell me how to do that ?

Thanks a lot,

Harshal
Harshal is offline   Reply With Quote

Old   April 11, 2014, 09:13
Default
  #12
Senior Member
 
plucas's Avatar
 
Anonymous
Join Date: Dec 2011
Location: USA
Posts: 108
Rep Power: 14
plucas is on a distinguished road
Your coefficients shouldn't change with speed.
plucas is offline   Reply With Quote

Old   April 11, 2014, 09:50
Default
  #13
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Quote:
Originally Posted by plucas View Post
Your coefficients shouldn't change with speed.
Hello Plucas,
thanks for your reply. Yes, you are right. Ideally, the Cd and Cl values should not change w.r.t speed. However, since the accuracy of results in CFD depend on numerous factors, it is quite possible that one does not get constant values for different inputs (here speed). So, I want to find out if the values change w.r.t speed and if they do, by how much.

Thanks again,

Harshal
Harshal is offline   Reply With Quote

Old   April 11, 2014, 23:12
Default
  #14
Senior Member
 
truffaldino's Avatar
 
Join Date: Jan 2011
Posts: 249
Blog Entries: 5
Rep Power: 17
truffaldino is on a distinguished road
Quote:
Originally Posted by plucas View Post
Your coefficients shouldn't change with speed.
Cl and Cd depend on reynolds number, i.e. on speed
truffaldino is offline   Reply With Quote

Old   April 12, 2014, 05:21
Default
  #15
Senior Member
 
lore
Join Date: Mar 2010
Location: Italy
Posts: 460
Rep Power: 18
lovecraft22 is on a distinguished road
Send a message via Skype™ to lovecraft22
Quote:
Originally Posted by Harshal View Post
1) Keep the car and the road at rest and give inlet velocity equal to the velocity of the car
As somebody already said, you need your road as a sliding wall if you want your car to be simulated in operating road conditions


Quote:
Originally Posted by Harshal View Post
2) Directly give the car it's velocity without creating a velocity inlet.
How would you do that? Sliding mesh?

Maybe the results would not change (I'm not completely sure though) but the cost of your simulation will change a lot.
lovecraft22 is offline   Reply With Quote

Old   April 12, 2014, 12:29
Default
  #16
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Quote:
Originally Posted by truffaldino View Post
Cl and Cd depend on reynolds number, i.e. on speed
Hello truffaldino,
thanks for your reply. I'll look further into this and see if and how the Cd and Cl will change with increasing speeds.
Harshal is offline   Reply With Quote

Old   April 12, 2014, 14:31
Default
  #17
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Quote:
Originally Posted by truffaldino View Post
Cl and Cd depend on reynolds number, i.e. on speed
Hello,
could you please tell me how the Cd and Cl values will change for increasing speeds (30 m/s, 40 m/s and 50 m/s).

Will both or any one of Cd and Cl increase / decrease with increasing speeds ?
Which parmeter of the two will change more than the other ?

Anything like that would be very helpful.

Thanks,

Harshal
Harshal is offline   Reply With Quote

Old   April 13, 2014, 16:19
Default
  #18
Senior Member
 
plucas's Avatar
 
Anonymous
Join Date: Dec 2011
Location: USA
Posts: 108
Rep Power: 14
plucas is on a distinguished road
Quote:
Originally Posted by truffaldino View Post
Cl and Cd depend on reynolds number, i.e. on speed
Yes it does at 100% theory level. In application, a vehicle at those speeds he requested, the coefficients should be the same.
plucas is offline   Reply With Quote

Old   May 7, 2014, 05:39
Default For which speed does a car manufacturer specify car's Cd value ?
  #19
Member
 
Harshal
Join Date: Oct 2013
Posts: 51
Rep Power: 12
Harshal is on a distinguished road
Hello,
I have a question regarding Cd value.
As I learned recently, the Cd value depends on the speed.
However, when car manufacturers declare the Cd value of a vehicle, I noticed that they simply mention the Cd value, without specifying the corresponding speed.

I have carried out several simulations for various speeds ranging from 30 m/s to 50 m/s and need to determine the accuracy of my results. For this, I am comparing my simulation values to the Cd value of 0.35 declared by the manufacturer.

However, I do not know for which speed the Cd value should be 0.35. Hence,I am unable to draw any conclusion from my results.

So, does anyone know how the Cd value of a vehicle is specified ? Is there any standard test cycle procedure like in case of fuel consumption, to determine the Cd ?

I would appreciate any insight or information regarding this.

Thanks,

Harshal
Harshal is offline   Reply With Quote

Old   May 8, 2014, 03:24
Default
  #20
Member
 
Join Date: Dec 2012
Posts: 92
Rep Power: 13
beer is on a distinguished road
Hi


Simply: No, the drag coefficient should be completely independent from the speed. It is a dimensionless coefficient and is made for comparing the aerodynamics of different shapes, even if speed, Reynold number and even size is different, think of airplane models in experiments (btw. these three always correlate anyway). This doesn't hold for all speed regimes but for a quite large regime the drag coefficient is indeed more or less reynold independent, which is surely what plucas meant, too.
The coefficient is defined as the proportion of the force on the body and the "possible force" from the flow around it, measured by the dynamic pressure.

cd = F / (rho/2 u^2 A)

The area A is some area which is characteristic for your body. Aerospace engineers use the wing area, car engineers use the projected front area of the car, usually without mirrors as far as I know.

Long story short. Let fluent calculate the force on your body aka on all body surfaces, divide the force by half of your density, the square of your inlet velocity and the projected surface of your car. Plot the cd for different velocities and you'll see they will be roughly the same. -> done

Have fun
beer is offline   Reply With Quote

Reply

Tags
aerodynamics, downforce, drag, vehicle, wind tunnel

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Vehicle Aerodynamics ac_ankit Main CFD Forum 9 February 3, 2014 14:28
External Vehicle Aerodynamics Torque_Converter CFX 7 October 23, 2013 14:49
Vehicle aerodynamics Anand Sis Main CFD Forum 2 July 23, 2013 01:42
[snappyHexMesh] Refinment Level for Vehicle External Aerodynamics danobis OpenFOAM Meshing & Mesh Conversion 0 February 18, 2013 07:37
Expert Systems, the key to vehicle aerodynamics CD adapco Group Marketing Siemens 0 March 19, 2003 10:11


All times are GMT -4. The time now is 09:20.