X-Foil Airfoil with gurney?

Yur · August 26, 2011, 11:33

Dear forum members,

I'm working on a double element wing, and I would like to know if there is a way to get reliable results for a wing with a gurney?

As I know that it's not possible to simulate multi element airfoils in X-Foil, I separate them and also simulate separatly, but on some way, X-Foil doesn't get the right chord lenght. So the simulation totally fails.

I organize all coordinates in Excel, so maybe there are some tricks to do it better.

Thanks.

truffaldino · August 26, 2011, 13:32

Why do not you fix the chord lenghth of each airfoil and change reynolds number instead?

What problem are you solving exactly? Is it a gurney flap which is separated from main airfoil? X-foil could be not a good choise for such kind of problems.

Truffaldino

Yur · August 27, 2011, 04:23

Well is there a way to change the chord length in X-Foil? The gurney is attached to the foil, so there are no gaps.

The problem is that X-Foil thinks that the gurney flap, is the chord length and doesn't recognize the LE.
The thing I would like to know is, if there's a proper way to put in the coordinates in Excel to let X-Foil recognize the right LE and TE.

Thanks.

truffaldino · August 27, 2011, 05:26

Quote:

Originally Posted by Yur

The problem is that X-Foil thinks that the gurney flap, is the chord length and doesn't recognize the LE.
Thanks.

I have just added a 2% gurney flap to naca0012 and loaded it to x-foil: everything seems to work. Xfoil recognizes LE and TE.

Bad panelling coul be also eliminated by tiny rounding the right angle.

For sure, your coordinate loading problem can be easily fixed, but it is not the main problem with x-foil. The real problem is more fundamental: the methods X-foil uses are not fitted for analyzing gurney flaps, and results you will get could have nothing to do with reality.

X-foil is based on integral boundary methods that do not handle vorticity regions that you have at gurney flaps, corners, steps etc.

Truffaldino

jemo · January 17, 2014, 05:32

Quote:

Originally Posted by truffaldino

I have just added a 2% gurney flap to naca0012 and loaded it to x-foil: everything seems to work. Xfoil recognizes LE and TE.

Bad panelling coul be also eliminated by tiny rounding the right angle.

For sure, your coordinate loading problem can be easily fixed, but it is not the main problem with x-foil. The real problem is more fundamental: the methods X-foil uses are not fitted for analyzing gurney flaps, and results you will get could have nothing to do with reality.

X-foil is based on integral boundary methods that do not handle vorticity regions that you have at gurney flaps, corners, steps etc.

Truffaldino

Can you share the dat file?

truffaldino · January 17, 2014, 13:44

Quote:

Originally Posted by jemo

Can you share the dat file?

Here it is. you could do fine repanelling (using standard x-foil/xflr procedures) closer to the flap

lovecraft22 · January 17, 2014, 14:13

I agree with truffaldino, what you are doing cannot be done with x-foil for two reasons:

1. It cannot handle multi element wings and the behavior of a main plane + flap all together is totally different from the behavior of each one of them alone since they influence each other.
2. A gurney tab works because of the flow separation it creates and this is not handled by X-foil

August 26, 2011, 11:33	X-Foil Airfoil with gurney?	#1
Yur New Member Join Date: Aug 2011 Posts: 17 Rep Power: 14	Dear forum members, I'm working on a double element wing, and I would like to know if there is a way to get reliable results for a wing with a gurney? As I know that it's not possible to simulate multi element airfoils in X-Foil, I separate them and also simulate separatly, but on some way, X-Foil doesn't get the right chord lenght. So the simulation totally fails. I organize all coordinates in Excel, so maybe there are some tricks to do it better. Thanks.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Low Speed Airfoil	Mancusi	FLUENT	7	April 3, 2014 06:11
[GAMBIT] Meshing airfoil using .dat file problem	creggie	ANSYS Meshing & Geometry	10	June 27, 2010 19:24
Grid resolution for an airfoil with a Gurney flap	alastormoody11	FLUENT	0	October 24, 2009 07:22
Modeling Backflow for a 3D Airfoil (Wing of Finite Span)	Josh	CFX	9	August 18, 2009 11:31
Airfoil boundary condition	Frank	Main CFD Forum	1	April 21, 2008 18:36

August 26, 2011, 13:32		#2
truffaldino Senior Member Join Date: Jan 2011 Posts: 249 Blog Entries: 5 Rep Power: 17	Why do not you fix the chord lenghth of each airfoil and change reynolds number instead? What problem are you solving exactly? Is it a gurney flap which is separated from main airfoil? X-foil could be not a good choise for such kind of problems. Truffaldino

August 27, 2011, 04:23		#3
Yur New Member Join Date: Aug 2011 Posts: 17 Rep Power: 14	Well is there a way to change the chord length in X-Foil? The gurney is attached to the foil, so there are no gaps. The problem is that X-Foil thinks that the gurney flap, is the chord length and doesn't recognize the LE. The thing I would like to know is, if there's a proper way to put in the coordinates in Excel to let X-Foil recognize the right LE and TE. Thanks.

January 17, 2014, 14:13		#7
lovecraft22 Senior Member lore Join Date: Mar 2010 Location: Italy Posts: 460 Rep Power: 18	I agree with truffaldino, what you are doing cannot be done with x-foil for two reasons: 1. It cannot handle multi element wings and the behavior of a main plane + flap all together is totally different from the behavior of each one of them alone since they influence each other. 2. A gurney tab works because of the flow separation it creates and this is not handled by X-foil