|
[Sponsors] |
March 26, 2017, 12:18 |
Meshing in Ansys fluent
|
#1 |
New Member
Bukhari
Join Date: Mar 2017
Posts: 8
Rep Power: 9 |
HI...I am doing hydro-dynamic analysis of an underwater vehicle(UWV). I want to refine mesh around UWV by dividing my fluid domain into sections.Can anyone please guide how to do it in ANSYS ICEM mesher. The image of domain I want to build is attached
|
|
March 26, 2017, 12:45 |
|
#2 |
New Member
A.MAROUF
Join Date: Dec 2016
Posts: 22
Rep Power: 9 |
Hi,
Well i recommand you not to split it in regions, try to have one mesh that is refined on the walls of your object and coarser else where, in ICEM you can at the first create block then divide it, after that create your edges (containing the number of elements) and there are some options to go from a refined to coarser mesh. Try to keep a structured mesh because your geometry is not that difficult. Good luck |
|
March 27, 2017, 05:38 |
|
#3 |
New Member
Bukhari
Join Date: Mar 2017
Posts: 8
Rep Power: 9 |
Thankx alot for your response.Can u further elaborate how to create blocks or how to make mesh finer near walls of Underwater vehicle??I am new to Ansys and need support, please.
|
|
March 27, 2017, 06:06 |
|
#4 |
New Member
A.MAROUF
Join Date: Dec 2016
Posts: 22
Rep Power: 9 |
Hey,
There are a lot of Tutorials on youtube, i recommand you to see the one with : ICEM Mesh for a Cylinder and NACA0012, try to follow the steps and i am sure that you will do it. if not you can send me your geometry and i will try to make you the mesh. Good luck |
|
March 27, 2017, 07:57 |
|
#5 |
New Member
Bukhari
Join Date: Mar 2017
Posts: 8
Rep Power: 9 |
bro I have tried alot using videos as well.Plz let me know your email ID for sending you my model.Plz try at ur end while I will also try again to mesh it.Thankx
|
|
March 27, 2017, 10:25 |
|
#6 |
New Member
A.MAROUF
Join Date: Dec 2016
Posts: 22
Rep Power: 9 |
i sent you my Email, look to your msg
|
|
March 27, 2017, 15:19 |
|
#7 |
New Member
Bukhari
Join Date: Mar 2017
Posts: 8
Rep Power: 9 |
dear bro...I have emailed you all data.plz check ur email
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
drag coefficient in ansys fluent 12.0 | krishna | FLUENT | 19 | April 12, 2018 00:49 |
Ansys Fluent NACA12 Meshing | researcher | ANSYS Meshing & Geometry | 0 | April 23, 2016 03:33 |
Ansys SIG$ILL error | loth | ANSYS | 3 | December 24, 2015 05:31 |
gambit in Ansys FLuent 13 | saharesobh | FLUENT | 0 | August 1, 2012 15:30 |
Meshing In Ansys Workbench For Fluent (Refinement) | FAU_OceanEng | FLUENT | 0 | May 31, 2010 17:12 |