CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Simulating air injecting to water in a tank?

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   March 12, 2009, 14:17
Default Simulating air injecting to water in a tank?
  #1
Howard Wang
Guest
 
Posts: n/a
Can any CFD code simulate air injects thru. a tube to water in a tank? I believe this is a problem of fluid interaction or fluid mixing, not multiphase flow.

Thanks, HW

  Reply With Quote

Old   March 12, 2009, 17:06
Default Re: Simulating air injecting to water in a tank?
  #2
Hrvoje Jasak
Guest
 
Posts: n/a
Have a look here - is this what you are after?

http://powerlab.fsb.hr/ped/kturbo/Op...pipeInTank.mpg

This is pretty straightforward 2-phase VOF stuff with a reasonably coarse mesh.

Hrv
  Reply With Quote

Old   March 12, 2009, 18:26
Default Re: Simulating air injecting to water in a tank?
  #3
Howard Wang
Guest
 
Posts: n/a
It is almost there. Additionally pressure loss in air injection may be interested for me.

Thank you very much, Hrvoje

HW
  Reply With Quote

Old   March 12, 2009, 19:08
Default Re: Simulating air injecting to water in a tank?
  #4
Model
Guest
 
Posts: n/a
your water level should rise right after the start of injection because of volume displacement. It does not seem your code is conserving liquid mass...
  Reply With Quote

Old   March 13, 2009, 03:10
Default Re: Simulating air injecting to water in a tank?
  #5
Hrvoje Jasak
Guest
 
Posts: n/a
The water level rises correctly - it's just that the tank has got a z-direction which is larger than what you see in the movie. The code is (of course) fully mass and momentum conservative - it would be quite difficult to write an FVM discretisation that does not conserve mass properly.

There is also a set of experimental comparison data for this case, if you are interested...

Hrv
  Reply With Quote

Old   March 13, 2009, 03:24
Default Re: Simulating air injecting to water in a tank?
  #6
Hrvoje Jasak
Guest
 
Posts: n/a
Let me guess: author with invalid E-mail address, using anonymous relay for posting. Please say Hello to Paul from me.

Hrv
  Reply With Quote

Old   March 13, 2009, 22:32
Default Re: Simulating air injecting to water in a tank?
  #7
Ahmed
Guest
 
Posts: n/a
Fact No 1: A good number of readers of this forum are interested and willing to run OpenFoam on their computers.

Fact No 2: A good number of them cannot even install the programme not to mention run it, for different reasons.

I think there are more negative than positive opinions about OpenFoam.

I guess it would be wise to see why there are angry opinions.

Anyway, I wish not to read harsh sarcastic replies.

FYI

I was able to install and run the programme, but I am not able to finish the first tutorial, I can display the mesh but not the scalar pressure field neither the vectorial velocity field and I do not know why, is there something missing or wrong with my installation, or may be I am not following the correct procedure
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
problem with two phase flow (air injected in water) miles_davis OpenFOAM 15 March 31, 2021 10:36
Filling Tank with Water leff CFX 7 August 21, 2017 08:47
Simulating air injecting to water in a tank? Howard Wang FLOW-3D 3 March 13, 2009 15:28
Simulating air jet into 2D & 3D water domain Imran FLUENT 0 June 6, 2006 09:57
Simulating Water Splash Using a Particle System Zi-Wei Chiou Main CFD Forum 0 March 4, 2002 07:33


All times are GMT -4. The time now is 00:47.