CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Pressure drop not correctly predicted

Register Blogs Members List Search Today's Posts Mark Forums Read

Like Tree2Likes

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   January 27, 2012, 14:01
Default Pressure drop not correctly predicted
  #1
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
I'm modeling an experiment with a flow obstruction and predicting the pressure drop that was measured in that test section. However, my prediction is about 26% under-predicted from the experimental results. This struck me as odd. I thought that pressure drop would be predicted better than experimental velocity, but experimental velocities are predicted to within 10%. What could I change in my simulation to improve my prediction of the pressure drop. I tried refining the mesh by doubling the number of cells, but that didn't cause any improvements in pressure drop prediction (but did improve the velocity prediction).
rks171 is offline   Reply With Quote

Old   January 27, 2012, 18:19
Default
  #2
Senior Member
 
Oliver Gloth
Join Date: Mar 2009
Location: Todtnau, Germany
Posts: 121
Rep Power: 17
ogloth is on a distinguished road
If velocities and flow topology are predicted correctly, my bet would be on skin friction. Check that the y+ requirements of your turbulence model are fulfilled. Good luck!
ogloth is offline   Reply With Quote

Old   January 27, 2012, 19:36
Default
  #3
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
Well, the accuracy of the flow velocity prediction is within about +- 10% for like 80% of the measurement points. I don't know if this should be considered good or not. I was using the realizable k-epsilon model with two-layer all y+ wall treatment. What kind of y+ values should I be targeting? My y+ values are between ~0.1 and 40. I thought that small and large y+ values were okay for all y+ wall treatment.

Another problem I just picked up on is my wall temperature calculations are about 30 Celsius off from experimental results, which seems like an awful lot to me. The surface area average temperature of the flow area matches up to experimental values within 1 Celsius, though, so it looks to me that the heat transfer coefficient at the wall is being badly predicted in addition to the skin friction coefficient, which again makes me think there's something wrong with the wall treatment. Any suggestions on how to improve that problem?
rks171 is offline   Reply With Quote

Old   January 27, 2012, 19:47
Default
  #4
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
What's your Mach number and what is the blockage ratio? And is your flow incompressible? If it is incompressible, average velocity coming in has to equal average velocity going out, assuming constant area. Conservation of mass. And the delta p is related to total loses. So how well are you predicting the drag on the obstruction and the WT walls? It is not surprising your velocity is better predicted than pressure loss. Also, how do you define pressure loss? Is it the average pressure loss upstream and downstream over the entire cross section area?
Martin Hegedus is offline   Reply With Quote

Old   January 27, 2012, 19:57
Default
  #5
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
Quote:
Originally Posted by rks171 View Post
Well, the accuracy of the flow velocity prediction is within about +- 10% for like 80% of the measurement points. I don't know if this should be considered good or not. I was using the realizable k-epsilon model with two-layer all y+ wall treatment. What kind of y+ values should I be targeting? My y+ values are between ~0.1 and 40. I thought that small and large y+ values were okay for all y+ wall treatment.

Another problem I just picked up on is my wall temperature calculations are about 30 Celsius off from experimental results, which seems like an awful lot to me. The surface area average temperature of the flow area matches up to experimental values within 1 Celsius, though, so it looks to me that the heat transfer coefficient at the wall is being badly predicted in addition to the skin friction coefficient, which again makes me think there's something wrong with the wall treatment. Any suggestions on how to improve that problem?
Maybe it would be good if you posted a picture. The topics of blockage and pressure loss is kind of generic.
Martin Hegedus is offline   Reply With Quote

Old   January 27, 2012, 20:29
Default
  #6
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
Mach number, I don't know... it's incompressible and the Reynolds number is about 100,000. Blockage ratio, I think, was about 30%, but I'll have to get back to you on that if that's important. I'll tell you what I did notice about the velocity predictions, though. In areas of the flow region where there is a higher ratio of wall to open flow area, the velocities are more severely under-predicted compared to the regions where there is a higher ratio of open flow area to wall, which is almost predicted perfectly. It seems like it's the shear at the wall that isn't being predicted right. Mass flow rate is conserved, I checked on that already.

The experiment had pressure drop measurements taken over several sections of the flow area - each section having the same type of flow blockage in it (a grid of complicated geometry). I'm calculating pressure drops over those same sections.

Interesting that you say it isn't surprising that pressure drop is poorly calculated compared to velocity. Why is that exactly?

What of the poor heat transfer between the wall and the fluid, resulting in the severe over-prediction of wall temperature? Can that problem not be related to the poor pressure drop prediction by a bad modeling of the wall effects in the turbulence model?

I don't think I'm going to be able to post a pic of this, as you requested, but think of metal straps with their thin sides oriented with the direction of the flow.
rks171 is offline   Reply With Quote

Old   January 27, 2012, 21:14
Default
  #7
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
Quote:
Originally Posted by rks171 View Post
Interesting that you say it isn't surprising that pressure drop is poorly calculated compared to velocity. Why is that exactly?
Conservation of mass and incompressibility. The flow into a stream tube must be equal to the flow coming out of the stream tube if the inlet and outlet areas are the same. If the velocity coming out of the stream tube is faster/slower than going in, then the area must have decreased/increased. Since you are in a confined area, that's tough to do. The flow is not as sensitive to it. Of course that is steady flow, but gives you an idea. The time averaged values for unsteady flow will behave sort of similar.

However, pressure is sensitive and is a reflection of the loss across the blockage (grid of complicated geometry)

So by saying that you are not capturing the pressure you are also saying that you are not capturing the drag on your blockage. Yes, there are possibly wall temperature affects, but if you can not get the drag on the blockage you have no hope of getting the pressure drop.

Not sure of what your blockage is, but it sounds like some sort of radiator. What is your Reynolds number length based on? If you are incompressible, it does not sound like your Reynolds number is based on the fins of the radiator (i.e. grid). What is your y+ on the radiator fins/metal straps? Sorry, your y+=1 for your metal straps must be based on a representative length of the metal straps. If I understand this correctly, you are going to have a lot of small cells. Ouch.
Martin Hegedus is offline   Reply With Quote

Old   January 28, 2012, 09:06
Default
  #8
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
That all makes sense.

My Reynolds number is based on the hydraulic diameter of my flow channel. Should I be aiming for a certain y+ value on the straps in order to better predict the wall drag? Is there a problem with having lots of small cells (aside from the computational demand)? Could that be the cause of my inability to correctly capture the wall shear?
rks171 is offline   Reply With Quote

Old   January 28, 2012, 12:59
Default
  #9
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
Quote:
Originally Posted by rks171 View Post
That all makes sense.

My Reynolds number is based on the hydraulic diameter of my flow channel. Should I be aiming for a certain y+ value on the straps in order to better predict the wall drag?
Depends if you are using wall functions or not. In general I do not recommend wall functions for complex geometries. If you don't use wall functions, then start of with y+ equal to 1 taken at about 1/4 of the characteristic length scale of your metal strap.

Quote:
Is there a problem with having lots of small cells (aside from the computational demand)?
In general, no, just computational demand

Quote:
Could that be the cause of my inability to correctly capture the wall shear?
I'm not exactly clear on your overall geometry so it is hard for me to say. However, pressure drop and entropy rise (i.e. temperature) is a very important part. This provides the "stuff" which changes everything downstream.

Another part is the equation of state. I deal with air and it sounds like you deal with a fluid (water?). It sounds like your blockage is significant in terms of creating entropy. For air, I would recommend using the compressible equations. I don't have a suggestion for a liquid. It sounds like your problem, in air, would cause a significant pressure drop and some sort of temperature rise. By the equation of state (perfect gas law), the density ratio of upstream and downstream would be affected noticeably, i.e. (rho1/rho2)=(p1/p2)*(T2/T1). Both the pressure drop and temperature rise push the density down. This then feeds back into the the other equations. I'm not sure what your equation of state is. But, for example, if your equation of state is equally sensitive to everything, like the perfect gas law, you need to use the full set of compressible equations. If density is not sensitive to pressure or temperature changes then you need to use the full set of incompressible N.S. equations. By this I mean that you need to include the energy equation and link it to the others by the equation of state. I assume you've done this since you have mentioned temperature. Sometimes the energy equation is dropped by neglecting temperature. And, finally, if temperature is not sensitive to pressure or density changes then the energy equation becomes decoupled from the other equations. In short, you need to use the right set of equations.

Turbulence modeling. And I'm referring to turbulence modeling around the obstruction, i.e. wake/eddy modeling. It will determine the drag on the obstruction. It will also determine how your pressure loss and entropy loss mix in with the rest of the flow. But, how important that second part is depends on where your measurements are taken. It sounds like your Re number is low. So, around the obstruction you may not have much choice in regards to turbulence modeling. Or I should say wake/eddy modeling. You will need to go with unsteady laminar (i.e. not LES or RANS) flow and do the best you can with the resources you have. All of which is maybe what you are doing now.

Oh, and at this point, all of my suggestions are just my opinions. It seems the physics you are modeling are complex due to significant interactions.
Martin Hegedus is offline   Reply With Quote

Old   January 28, 2012, 13:08
Default
  #10
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
BTW, you mentioned flow channel. Does this mean something like a water channel with the top surface exposed to air?

If so, there is a lot going on. Much more than I thought when this thread started!
Martin Hegedus is offline   Reply With Quote

Old   January 28, 2012, 13:29
Default
  #11
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
Ooops, I should be clear. Assuming adiabatic wall conditions, the only ingredient added by the obstruction is entropy.
Martin Hegedus is offline   Reply With Quote

Old   January 28, 2012, 13:58
Default
  #12
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
Quote:
Depends if you are using wall functions or not. In general I do not recommend wall functions for complex geometries. If you don't use wall functions, then start of with y+ equal to 1 taken at about 1/4 of the characteristic length scale of your metal strap.
Do I have a choice whether or not I use a wall function? I thought I needed to use one with the k-epsilon turbulence model. Right now I'm using two-layer all y+ wall treatment.

As for temperature, I should clarify, I'm running several cases. Some are heated and temperature is important. Some are unheated and temperature change is insignificant. The flow is incompressible (water). For the case where I'm comparing the pressure to the experimental values, the case is not heated and so I don't include the energy equation, just continuity and momentum.

I don't think my Re is low (100,000), well into the turbulent region. I used k-epsilon first, but I think I'm going to try out k-omega and see what difference that makes.

There is no air above the vertically oriented channel, it's totally filled with water. It is a flow loop.
rks171 is offline   Reply With Quote

Old   January 28, 2012, 15:03
Default
  #13
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
To me, it sounds like you have TWO things you are trying to model. You are trying to model the obstruction and you are trying to model the channel. The obstruction just happens to be in the channel. The Reynolds number of 100,000 is for the channel since it is based on the hydraulic diameter of the flow channel. That will give you the y+ and turbulence model requirements for the CHANNEL WALLS. However, 100,000 is NOT the Reynolds number for the obstruction. The Reynolds number for the obstruction MUST be based on a representative characteristic of the OBSTRUCTION. For example, the maximum width of your metal staps. Or another way to think about it is this. How would you model the obstruction if it was not in the channel?

BTW, I goofed on the entropy statement. The obstruction is adding entropy and enthalpy because of work done by viscosity. I was thinking Euler equations.
Martin Hegedus is offline   Reply With Quote

Old   January 28, 2012, 16:55
Default
  #14
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
Have you tried comparing to an experiment without the obstruction?
Martin Hegedus is offline   Reply With Quote

Old   January 28, 2012, 18:28
Default
  #15
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
Yes, I'm sorry I was not clear about that before. I'm trying to model the entire experimental test section, which includes both the obstructions and the bare flow region. You are correct that Re is based off of the hydraulic diameter of the bare region. However, I thought since the velocity increases in the vicinity of the obstruction and since there is a small drop in the hydraulic diameter, then the Re doesn't drop much or at all. Certainly, I'm sure the flow is not laminar in that region of the obstruction. The obstruction acts to increase mixing of the fluid in its vicinity. But I guess what it comes down to is what should my y+ values be for the bare region and the obstruction region? Or how could I find that out? Is it possible that my y+ values of <1 are actually too small?

As for your question about the behavior outside of the obstruction (in the bare region), my calculated wall temperatures for the heated walls are consistently off by about 30 degree celsius, even far away from the obstructions (>15 L/D). For all I know, the obstruction modeling might not even be a problem, or a very small one. It might mainly be wall shear and wall heat transfer being incorrectly modeled in the bare region (which is much larger than the region of the obstruction).
rks171 is offline   Reply With Quote

Old   January 28, 2012, 22:59
Default
  #16
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
It is my opinion that on the wall of the channel in the region of the obstruction (assuming the obstruction goes all the way to the wall) and on the obstruction itself you can not use wall functions. Therefore the y+ must be less than 1.
Martin Hegedus is offline   Reply With Quote

Old   January 29, 2012, 00:37
Default
  #17
akj
New Member
 
anil
Join Date: Jun 2011
Location: chennai
Posts: 20
Rep Power: 14
akj is on a distinguished road
as far as i know ur y+ values should be between 0- 5 then only u will get satisfactory results. The reason for this may be the mesh so i thnik u have to refine ur mesh.

Regards,

Anil
aaryan likes this.
akj is offline   Reply With Quote

Old   January 29, 2012, 12:19
Default
  #18
Member
 
Join Date: Dec 2011
Location: State College, PA
Posts: 87
Rep Power: 14
rks171 is on a distinguished road
I've seen other posts where ppl said y+ should be above 30 always, however, I think that's if you're using a high y+ wall treatment. I'll check how the y+ differs between the obstructions and the wall of the test section.

The obstruction does touch the wall, but the obstruction is less than 10 mm long whereas the bare section of the flow area is over 200 mm long. I'm running a case using k-omega. I'll see how that works out and report back; however, I'm still using the same wall treatment. I'll also toy with my prism layers and see what that does.

Thanks for all the suggestions. I'll report back with what happens.
rks171 is offline   Reply With Quote

Old   January 29, 2012, 16:49
Default
  #19
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
I'm assuming your obstruction is a grid of metal straps with the wide flat side facing the flow vector, this is used for mixing, and you mentioned that the obstruction is 30%.

The Cd for a flat plate, with the flat side facing into the flow vector is 1.98 based on its surface area. The Cd based on a reference area of your cross section is basically 0.6 (i.e. 0.3*1.98). This corresponds to a Cp loss of 0.6. This value is also about the same as the head loss of a thin plate orifice with a beta of 0.5 (i.e. sqrt of 30%)

From the Moody Chart, assuming smooth walls and an Re of 100,000 based on diameter, the friction factor is 0.018.

Therefore it takes 33.3 L/Ds (0.6/0.018) before the head loss from the channel walls is equal to the head loss from the obstruction.

I guess I don't understand why your focus is on the walls. Head losses through orifices, and that is what your grid of straps sounds like, is huge. So, I guess I totally misunderstand your geometry and/or what you are measuring.

Here is another way to look at it. Compare the drag due friction on your channel walls to the drag of your obstruction. This may help direct your focus.
Martin Hegedus is offline   Reply With Quote

Old   January 29, 2012, 17:32
Default
  #20
Senior Member
 
Martin Hegedus
Join Date: Feb 2011
Posts: 500
Rep Power: 19
Martin Hegedus is on a distinguished road
I'm going to be straight forward and I am sorry if I misunderstand things. And, I know I don't understand the big picture. But it sounds like you believe that only the wall friction contributes to the head loss. This is not true. Separation from the obstruction also contributes. And it could contribute a lot.
qutadah.r likes this.
Martin Hegedus is offline   Reply With Quote

Reply

Tags
pressure drop, wall drag

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Pipe Flow - Pressure Drop Daniel L FLOW-3D 2 December 10, 2010 05:23
Total and Static Pressure drop Jaggu FLUENT 3 December 9, 2008 07:03
Estimating pressure drop from the shear stresses K.Baker FLUENT 2 July 26, 2007 04:56
Periodic boundaries and pressure drop MatejK CFX 2 July 12, 2005 05:47
Hydrostatic pressure in 2-phase flow modeling (CFX4.2) HB &DS CFX 0 January 9, 2000 14:19


All times are GMT -4. The time now is 07:51.