CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

unexpected results

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   October 3, 2005, 01:42
Default unexpected results
  #1
Kevin Rogers
Guest
 
Posts: n/a
My son is doing science project regarding action and reaction of the boat propelled by a water jet through a straw connected to a water tank on the boat. Got surprisingly unexpected results.

There are 2-sets of experiments depending on the water amount of the water released. Both started with full-tank water.

1st set is half release(from top to mid-level of tank) and 2nd set is full release of water of water from the tank.

The average velocity of the boat is greater in the case of half water release. Why? I could not give him why.

Thanks.

  Reply With Quote

Old   October 3, 2005, 02:12
Default Re: unexpected results
  #2
diaw
Guest
 
Posts: n/a
Off the top of my head. Perform a momentum balance on the boat. As the water level drops, so does the relative thrust due to 'potential head' getting lower, but, at the same time, the momentum of the boat also reduces - & I guess the thrust per momentum loss reduces as the level drops. It must be balanced by friction on boat sides.

There will no doubt be a break-even point. The first case should be better, with performance dropping until it hits the breakeven point.

So, back to your Newton's Second Law you go...

diaw...
  Reply With Quote

Old   October 3, 2005, 02:20
Default Re: unexpected results
  #3
Praveen. C
Guest
 
Posts: n/a
This is a guess. When you start with a full tank, the boat is heavier and probably experiences more drag since the boat is immersed to larger amount in the water. When you start with half tank, drag might be less and hence you see larger velocity.
  Reply With Quote

Old   October 3, 2005, 12:24
Default Re: unexpected results
  #4
Jack
Guest
 
Posts: n/a
I see that you are measuring average speed. Does the boat travel the same distance in each case? If the boat travels farther when emptying the whole water tank, then it is reasonable to assume that the boat gradually loses its speed as the pressure is reduced by the emptying of its water tank. If you average the speed over the distance traveled, then it might seem as if it travels "slower" overall. Is this what happened?

  Reply With Quote

Old   October 3, 2005, 12:47
Default Re: unexpected results
  #5
Kevin Roe
Guest
 
Posts: n/a
Well, for both cases, starting water levels are from the top. Only end level of water is different, one case to the moddle, and the other case to thr bottom. So, they experience the same drag at least until the water level reaches the middle level of the tank.

-Kevin
  Reply With Quote

Old   October 3, 2005, 12:51
Default Re: unexpected results
  #6
Kevin R.
Guest
 
Posts: n/a
Of course, the case of releasing full water traveled longer distance compared to the half-water release case.

As you said, "If you average the speed over the distance traveled, then it might seem as if it travels "slower" overall" can explain what happened. But still not sure.

-Kevin R.
  Reply With Quote

Old   October 3, 2005, 18:08
Default Re: unexpected results
  #7
Mani
Guest
 
Posts: n/a
I also think that's what it is. The momentum that the boat gets from the water jet depends on the velocity of the jet, which depends on the pressure in the tank. As the water level drops in the tank, so does the pressure. Jet and boat will be faster in the first half of the experiment, and should slow down significantly towards the end. There are some other effects countering this, and it really depends on your boat, but maybe the influence of pressure is dominant, here. Anyway, the average velocity is certainly larger if only considering the fast period.

I suggest one relatively easy way to verify this: Starting with a full tank, measure distance and time the boat travels >after< the tank is half empty, i.e. measure only the second half of the experiment. You should see that this will give you a relatively small velocity (even smaller than the overall velocity). The overall average velocity (completely emptying the tank) should be somewhere between the average velocity of the first part (which is large), and the average velocity of the second part (which is small).

  Reply With Quote

Old   October 6, 2005, 12:34
Default Re: unexpected results
  #8
ZubenUbi
Guest
 
Posts: n/a
Could it be that : Due to viscous force, a box filled of water will travel a shorter distance than the same box filled with a solid of same mass. Of course, both box have the same initial conditions...
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
OpenFOAM - Validation of Results Ahmed OpenFOAM Running, Solving & CFD 10 May 13, 2018 19:28
wind tunnel results vs fluent pixie Main CFD Forum 1 August 20, 2009 09:02
Velocity spots in openFoam results Valle OpenFOAM Running, Solving & CFD 4 August 19, 2009 06:53
How to plot a function over a time period? Cirion0000 CFX 4 July 18, 2009 13:48
how to view the complete results shokry FLOW-3D 5 February 3, 2009 14:56


All times are GMT -4. The time now is 05:32.