CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Special Topics > Mesh Generation & Pre-Processing

Salome - Geometry

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   July 23, 2018, 06:51
Default Salome - Geometry
  #1
New Member
 
Thuraya
Join Date: Jul 2016
Location: Japan
Posts: 2
Rep Power: 0
Thuraya is on a distinguished road
after installing Salome Salome-V8_4_0-univ_public on Ubuntu 18.04 I faced this problem where I cannot enter new entities like 2D /3D sketch The error message is:
GUI library corresponding to the users action can not be found or loaded.

the terminal has the following message too.

************************************************** **************
Warning: module HEXABLOCKPLUGIN is improperly configured!
Module HEXABLOCKPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module HYBRIDPLUGIN is improperly configured!
Module HYBRIDPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module BLSURFPLUGIN is improperly configured!
Module BLSURFPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module HexoticPLUGIN is improperly configured!
Module HexoticPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module GMSHPLUGIN is improperly configured!
Module GMSHPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module NETGENPLUGIN is improperly configured!
Module NETGENPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module GHS3DPLUGIN is improperly configured!
Module GHS3DPLUGIN will not be available in GUI mode!
Thuraya is offline   Reply With Quote

Old   September 2, 2018, 05:51
Default same problem here
  #2
New Member
 
Stefan Karrer
Join Date: Sep 2018
Posts: 1
Rep Power: 0
siliconverter is on a distinguished road
I installed salome meca 2018 on a ubuntu 18.04 which was freshly installed.


I had to install python 2.7 and gcc and install libcanberra-gtk0 libcanberra-gtk-module
finally net-tools.
Also disable 3 faulty drivers at $HOME/salome_meca/V2018/prerequisites/debianForSalome/lib/libstdc++.*


Now Salome Meca 2018 starts with the following warnings:


stefan@ubuntu-engineering:~/salome_meca/appli_V2018$ ./salome
runSalome running on ubuntu-engineering
Searching for a free port for naming service: 2810 - OK
Searching Naming Service + found in 0.1 seconds
Searching /Kernel/Session in Naming Service +++++Warning: this type (SALOME_MED/MEDCouplingFieldDoubleCorbaInterface,objref) already exists, it will be ignored.
found in 2.5 seconds
Start SALOME, elapsed time : 2.7 seconds
************************************************** **************
Warning: module NETGENPLUGIN is improperly configured!
Module NETGENPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module GMSHPLUGIN is improperly configured!
Module GMSHPLUGIN will not be available in GUI mode!
************************************************** **************
************************************************** **************
Warning: module HYBRIDPLUGIN is improperly configured!
Module HYBRIDPLUGIN will not be available in GUI mode!
************************************************** **************



Would be nice if someone had a suggestion on how to resolve these Warnings.
siliconverter is offline   Reply With Quote

Reply

Tags
geometry, salome

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
[ANSYS Meshing] CATIA Geometry Generation and Meshing danielsullivan ANSYS Meshing & Geometry 0 April 3, 2017 22:11
[Salome] unexpected geometry : topology of source and target faces seems different salome 6863523 OpenFOAM Meshing & Mesh Conversion 8 March 9, 2017 05:24
[Salome] how to create geometry with salome to make "IdeasUnvToFoam" working! amorenelchino OpenFOAM Meshing & Mesh Conversion 5 June 24, 2013 11:35
Problem Importing Geometry ProE to CFX fatb0y CFX 3 January 14, 2012 20:42
[Salome] Salome Geometry question (Pipe with certain wall thickness) Hectux OpenFOAM Meshing & Mesh Conversion 1 April 8, 2009 07:44


All times are GMT -4. The time now is 00:17.