paraFoam = freeze

danFoam · February 9, 2010, 16:16

Now I have installed openFoam1.6 in several ways, with different Qt etc (including following the instructions in the readme file, installation of Qt 4.3.5 and building paraView from source).

No matter what I do I get the same result; when i run paraFoam ParaView opens and then the whole system freezes completely. No error messages. I can see the ParaView window including the cavity.OpenFoam-file in the pipeline browser but the computer is no longer responding to anything. Reboot is the only option.

System: Hp Compaq nx7010, Ubuntu 9.10

Any ideas?

danFoam · February 12, 2010, 11:51

I used blockMesh, icoFoam and then paraFoam. (Running the cavity tutorial.)

I built paraview from source using the command where the path of the qt is given.

I then realized that paraview freeze even if I open it as a stand alone program (not using paraFoam).

Finally i gave in and decided to run paraview on another computer and then use foamToVtk and simply open the vtk-file. I installed paraview on a windows computer (Vista), just to encounter the exact same problem. When I open paraview the computer freeze. Then I tried on a third computer (Win 7) and finally paraview runs. So now it almost works, except that my vtk-files seem to miss some properties...

Why paraview freeze - still don't know. Maybe it requires a lot of memory!?

danFoam · February 12, 2010, 11:52

By the way. I also tried with another Linux distribution (openSuse). No difference.

danFoam · February 12, 2010, 13:50

First of all, thanks a lot for trying to help out!!!

1) Yes.

2) Yes. I'd say about 2 hours.

3) I belive so:

cd $WM_THIRD_PARTY_DIR
rm -rf paraview-3.6.1/platforms
makeParaView

qmake is installed.

I don't recognize the error message you mentioned.

4) Note that paraview freezes even without the cavity file. If I simply type paraview in the terminal it opens, I may see the user interface etc. and then everything freeze...

lin · February 23, 2010, 08:27

I have same problem.Paraview freeze the computer(hp 6530b). From results of all methods i have tried,I think the problem is related to graphic card I use, the intel 4 series,if I remember correctly. Using the vesa driver intead of intel driver may fix the problem.

February 9, 2010, 16:16	paraFoam = freeze	#1
danFoam New Member Dan Join Date: Feb 2010 Posts: 4 Rep Power: 16	Now I have installed openFoam1.6 in several ways, with different Qt etc (including following the instructions in the readme file, installation of Qt 4.3.5 and building paraView from source). No matter what I do I get the same result; when i run paraFoam ParaView opens and then the whole system freezes completely. No error messages. I can see the ParaView window including the cavity.OpenFoam-file in the pipeline browser but the computer is no longer responding to anything. Reboot is the only option. System: Hp Compaq nx7010, Ubuntu 9.10 Any ideas?

February 12, 2010, 13:50		#4
danFoam New Member Dan Join Date: Feb 2010 Posts: 4 Rep Power: 16	First of all, thanks a lot for trying to help out!!! 1) Yes. 2) Yes. I'd say about 2 hours. 3) I belive so: cd $WM_THIRD_PARTY_DIR rm -rf paraview-3.6.1/platforms makeParaView qmake is installed. I don't recognize the error message you mentioned. 4) Note that paraview freezes even without the cavity file. If I simply type paraview in the terminal it opens, I may see the user interface etc. and then everything freeze...

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[OpenFOAM] surfaceScalarField in paraFoam	danielr	ParaView	1	October 5, 2009 02:08
[OpenFOAM] Segmentation fault with paraFoam and paraview 3.6.1 on Fedora 11 32 and 64 bit	nanes	ParaView	2	September 11, 2009 09:12
[OpenFOAM] ParaFOAM visualization problems	robbo	ParaView	0	March 15, 2008 14:10
[OpenFOAM] Parafoam basic questions	qtian	ParaView	0	July 20, 2007 11:52
[OpenFOAM] ParaFoam OF 14 decomposed cases	philippose	ParaView	4	April 18, 2007 05:17

February 12, 2010, 11:51		#2
danFoam New Member Dan Join Date: Feb 2010 Posts: 4 Rep Power: 16	I used blockMesh, icoFoam and then paraFoam. (Running the cavity tutorial.) I built paraview from source using the command where the path of the qt is given. I then realized that paraview freeze even if I open it as a stand alone program (not using paraFoam). Finally i gave in and decided to run paraview on another computer and then use foamToVtk and simply open the vtk-file. I installed paraview on a windows computer (Vista), just to encounter the exact same problem. When I open paraview the computer freeze. Then I tried on a third computer (Win 7) and finally paraview runs. So now it almost works, except that my vtk-files seem to miss some properties... Why paraview freeze - still don't know. Maybe it requires a lot of memory!?

February 12, 2010, 11:52		#3
danFoam New Member Dan Join Date: Feb 2010 Posts: 4 Rep Power: 16	By the way. I also tried with another Linux distribution (openSuse). No difference.

February 23, 2010, 08:27		#5
lin Senior Member Hua Zen Join Date: Mar 2009 Posts: 138 Rep Power: 17	I have same problem.Paraview freeze the computer(hp 6530b). From results of all methods i have tried,I think the problem is related to graphic card I use, the intel 4 series,if I remember correctly. Using the vesa driver intead of intel driver may fix the problem.