[OpenFOAM.com] paraview error Not downloading ParaView (version <= 5.0.1)

assassinH · May 13, 2022, 12:19

hi
i'm installing paraview in terminal (debian) and i get this error

$ ./makeParaView
Not downloading ParaView (version <= 5.0.1)...
did not find ParaView- in these directories:
WM_THIRD_PARTY_DIR=/home/wormho1e/OpenFOAM/ThirdParty-9
abort build

I dont find similar error in formu. Does anyone has ideas about it?

Thanks

Fschhh · September 9, 2023, 08:10

I'm having the same issue with OpenFoam-dev (.org version). This is the only post I can find on the whole Internet mentioning this error. I'll update if I solve it.
https://xkcd.com/979/

Fschhh · September 9, 2023, 11:53

The cause was the environment $ParaView_VERSION that was empty.

The reason for this was that OpenFOAM/OpenFOAM-dev/etc/config.sh/paraview tried to look for cmake in OpenFOAM/ThirdParty-dev/platforms/linux64Gcc/cmake-*, which doesn't exist, and it crashed before defining ParaView_VERSION. Actually, OpenFOAM/ThirdParty-dev/platforms/linux64Gcc doesn't even exist, only OpenFOAM/ThirdParty-dev/platforms/linux64GccDPInt32, but even that folder doesn't contain any cmake.

I just commented out the lines looking for cmake. The build started, crashed at some point, but I figured it was easier to use Paraview installed normally from the package manager instead.

May 13, 2022, 12:19	paraview error Not downloading ParaView (version <= 5.0.1)	#1
assassinH New Member Juie Bi Join Date: May 2022 Posts: 1 Rep Power: 0	hi i'm installing paraview in terminal (debian) and i get this error $ ./makeParaView Not downloading ParaView (version <= 5.0.1)... did not find ParaView- in these directories: WM_THIRD_PARTY_DIR=/home/wormho1e/OpenFOAM/ThirdParty-9 abort build I dont find similar error in formu. Does anyone has ideas about it? Thanks

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OpenFOAM-1.6 install cookbook	MadsR	OpenFOAM Installation	372	November 20, 2010 12:57
paraFoam reader for OpenFOAM 1.6	smart	OpenFOAM Installation	13	November 16, 2009 22:41
[OpenFOAM] Using Fedora 11 Repository Version of ParaView	mturcios777	ParaView	0	July 30, 2009 18:49
[OpenFOAM] ParaView patch visualisation error in Development version	philippose	ParaView	17	March 26, 2007 07:45
[OpenFOAM] ParaFoam conflicting version of paraview	xponticq	ParaView	3	May 16, 2006 13:52

September 9, 2023, 08:10		#2
Fschhh New Member Guillaume Chauvat Join Date: Sep 2023 Location: Stockholm, Sweden Posts: 4 Rep Power: 3	I'm having the same issue with OpenFoam-dev (.org version). This is the only post I can find on the whole Internet mentioning this error. I'll update if I solve it. https://xkcd.com/979/

September 9, 2023, 11:53		#3
Fschhh New Member Guillaume Chauvat Join Date: Sep 2023 Location: Stockholm, Sweden Posts: 4 Rep Power: 3	The cause was the environment $ParaView_VERSION that was empty. The reason for this was that OpenFOAM/OpenFOAM-dev/etc/config.sh/paraview tried to look for cmake in OpenFOAM/ThirdParty-dev/platforms/linux64Gcc/cmake-*, which doesn't exist, and it crashed before defining ParaView_VERSION. Actually, OpenFOAM/ThirdParty-dev/platforms/linux64Gcc doesn't even exist, only OpenFOAM/ThirdParty-dev/platforms/linux64GccDPInt32, but even that folder doesn't contain any cmake. I just commented out the lines looking for cmake. The build started, crashed at some point, but I figured it was easier to use Paraview installed normally from the package manager instead.