[blockMesh] Graded Mesh Calculator

Nikunj.R · November 12, 2012, 14:51

Hello All!

I wanted to determine the size of cells when using grading. In the example that I am running, the length of the block is 1.2 m, with 20 cells in the direction where grading is applied and 0.05 is the ratio (between the first cell and the last cell). How can i know the length of each cell in the graded direction. I know that gradind calculator has been presented here, but extracting it is giving errors.

Thanks for your help.

Regards,
Nikunj.

wyldckat · November 12, 2012, 17:06

Greetings Nikunj,

I'm sorry to say I can't help you with this (no time to test), but I know that the plug-in SwiftBlock for Blender might help you: http://openfoamwiki.net/index.php/SwiftBlock
I say this because of this post: http://www.cfd-online.com/Forums/ope...tml#post390786 - post #48

Best regards,
Bruno

Nikunj.R · November 14, 2012, 10:09

Thanks for your reply Bruno! It was really helpful.

Regards,
Nikunj.

November 12, 2012, 14:51	Graded Mesh Calculator	#1
Nikunj.R Member Nikunj Raithatha Join Date: Jul 2012 Location: Washington DC Posts: 47 Rep Power: 13	Hello All! I wanted to determine the size of cells when using grading. In the example that I am running, the length of the block is 1.2 m, with 20 cells in the direction where grading is applied and 0.05 is the ratio (between the first cell and the last cell). How can i know the length of each cell in the graded direction. I know that gradind calculator has been presented here, but extracting it is giving errors. Thanks for your help. Regards, Nikunj.

November 12, 2012, 17:06		#2
wyldckat Retired Super Moderator Bruno Santos Join Date: Mar 2009 Location: Lisbon, Portugal Posts: 10,975 Blog Entries: 45 Rep Power: 128	Greetings Nikunj, I'm sorry to say I can't help you with this (no time to test), but I know that the plug-in SwiftBlock for Blender might help you: http://openfoamwiki.net/index.php/SwiftBlock I say this because of this post: http://www.cfd-online.com/Forums/ope...tml#post390786 - post #48 Best regards, Bruno __________________ OpenFOAM: FAQ \| Getting started Forum: How to get help, to post code/output and forum guide Read this before sending me PM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] conformed FSI mesh for unstructured fluid region	ashish.svm	OpenFOAM Meshing & Mesh Conversion	10	August 2, 2019 08:40
[snappyHexMesh] snappyHexMesh does not create any mesh except one for the reference cell	Arman_N	OpenFOAM Meshing & Mesh Conversion	1	May 20, 2019 17:16
[snappyHexMesh] Creating multiple multiple cell zones with snappyHexMesh - a newbie in deep water!	divergence	OpenFOAM Meshing & Mesh Conversion	0	January 23, 2019 04:17
[ICEM] 2D hybrid mesh (unstructured mesh highly dependent on structured mesh parameters)	shubham jain	ANSYS Meshing & Geometry	1	April 10, 2017 05:03
[snappyHexMesh] Snappyhex mesh: poor inlet mesh	Swagga5aur	OpenFOAM Meshing & Mesh Conversion	1	December 3, 2016 16:59

November 14, 2012, 10:09		#3
Nikunj.R Member Nikunj Raithatha Join Date: Jul 2012 Location: Washington DC Posts: 47 Rep Power: 13	Thanks for your reply Bruno! It was really helpful. Regards, Nikunj.