|
[Sponsors] |
July 11, 2014, 22:11 |
How to mesh it with blockMesh
|
#1 |
New Member
xurenyi
Join Date: Apr 2014
Posts: 10
Rep Power: 12 |
blocks
( hex (14 13 37 38 15 16 40 39 ) (18 20 20) simpleGrading (1 1 1) hex (13 12 36 37 16 17 41 40 ) (20 20 20) simpleGrading (1 1 1) hex (12 11 35 36 17 18 42 41 ) (10 20 20) simpleGrading (1 1 1) hex (11 10 34 35 18 19 43 42 ) (5 20 20) simpleGrading (1 1 1) hex (10 9 33 34 19 20 44 43 ) (5 20 20) simpleGrading (1 1 1) hex (9 8 32 33 20 21 45 44 ) (5 20 20) simpleGrading (1 1 1) hex (8 7 31 32 21 22 46 45 ) (5 20 20) simpleGrading (1 1 1) hex (7 6 30 31 22 23 47 46 ) (25 20 20) simpleGrading (1 1 1) hex (6 5 29 30 23 2 26 47 ) (5 20 20) simpleGrading (1 1 1) hex (23 2 26 47 0 1 24 25 ) (3 20 20) simpleGrading (1 1 1) hex (5 4 28 29 2 3 27 26 ) (50 20 20) simpleGrading (1 1 1) ); --> FOAM FATAL ERROR: Inconsistent number of faces between block pair 8 and 9 From function blockMesh::calcMergeInfo() in file blockMesh/blockMeshMerge.C at line 221. The body (23 2 26 47 0 1 24 25 ) can never be connected with others. How to handle this body? |
|
August 13, 2014, 09:21 |
|
#2 |
Senior Member
Join Date: Mar 2010
Location: Germany
Posts: 154
Rep Power: 16 |
Hi,
the error message says it all. First check the coordinates and the ordering of your vertices. Then check the discretization of adjoining blocks. Please provide the whole blockMeshDict. This will make it much easier for others to look at your problem! Cutter |
|
August 13, 2014, 09:36 |
|
#3 |
New Member
Lorenzo Gomes
Join Date: Nov 2013
Location: Brazil
Posts: 12
Rep Power: 12 |
Hi there,
whenever you have faces matching eachother they must have the same number of cells otherwise you have to use the function mergepatchṕairs at the bottom of the blockmeshdict file. If you post the code it will be easier to give you a better answer, Good luck. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[ICEM] 2D hybrid mesh (unstructured mesh highly dependent on structured mesh parameters) | shubham jain | ANSYS Meshing & Geometry | 1 | April 10, 2017 05:03 |
[snappyHexMesh] Snappyhex mesh: poor inlet mesh | Swagga5aur | OpenFOAM Meshing & Mesh Conversion | 1 | December 3, 2016 16:59 |
Star CCM Overset Mesh Error (Rotating Turbine) | thezack | Siemens | 7 | October 12, 2016 11:14 |
[snappyHexMesh] SnappyHexMesh for internal Flow | vishwa | OpenFOAM Meshing & Mesh Conversion | 24 | June 27, 2016 08:54 |
[blockMesh] blockMesh to generate the mesh of a deep cavity | eddykendo | OpenFOAM Meshing & Mesh Conversion | 4 | July 5, 2015 16:54 |