|
[Sponsors] |
[Commercial meshers] Origin 0 0 0 has been moved while fluentMeshToFoam |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
July 25, 2005, 12:55 |
Origin 0 0 0 has been moved while fluentMeshToFoam
|
#1 |
New Member
Jun Ishimoto
Join Date: Mar 2009
Location: Sendai, Miyagi, Japan
Posts: 5
Rep Power: 17 |
When I converted the Fluent mesh to the Foam mesh by using fluentMeshToFoam, the origin (0, 0, 0) moves different point.
Also the numbers of vertices are re-numbered and the order of the all vertices has been changed. I want to know: 1. How to fix origin (0 0 0) while converting to the Foam mesh? 2. Why the reference pressure (pRefCell) should be set to the close point to origin? I think that it is not necessary to place the pRefCell near the origin. Does anyone know the countermeasure for these problems? |
|
July 25, 2005, 14:11 |
1. Is this a 2D mesh? It will
|
#2 |
Senior Member
Mattijs Janssens
Join Date: Mar 2009
Posts: 1,419
Rep Power: 26 |
1. Is this a 2D mesh? It will offset points (OpenFOAM meshes are 3D)
In 3D points are read in order from the fluent file. 2. No need to set it close to the origin. Any cell is fine. |
|
July 26, 2005, 07:01 |
I created the Fluent mesh as s
|
#3 |
New Member
Jun Ishimoto
Join Date: Mar 2009
Location: Sendai, Miyagi, Japan
Posts: 5
Rep Power: 17 |
I created the Fluent mesh as same as:
/tutorials/icoFoam/cavity There is 1-mesh thickness in the z-direction (3D). I think this mesh is the most simple mesh, however, the origin (0 0 0) has been moved another point while the fluentMeshToFoam operation. |
|
July 26, 2005, 07:45 |
Yes the points are renumbered
|
#4 |
Senior Member
Join Date: Mar 2009
Posts: 854
Rep Power: 22 |
Yes the points are renumbered during the 1 cell layer extrusion process. If you are unhappy with this renumbering you can change fluentMeshToFoam to store the previous ordering are reapply it after the mesh conversion process but you will also have to decide how you would like the extruded points numbered.
|
|
May 20, 2013, 04:53 |
Moving Origin
|
#5 |
New Member
CFD
Join Date: Jan 2013
Posts: 23
Rep Power: 13 |
Hi Everyone!
This is an old thread but I have somehow a quite similar problem and hope someone could give me direction. What I should do if I want to convert fluent mesh to openfoam format using fluent3DMeshToFoam AND move the origin from (0 0 0) to (0 0 -30). Is it possible to do that? note: - it is a 3D geometry model - I have no access to the ansys software originaly made that particular fluent mesh - the change of origin point(0 0 0) somehow is important in my case Any suggestion would be greatly apreciated. Thanks in advances, warm regards, .:siefdi- |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
sampleDict not working (undefined keyword origin) | jet_engine | OpenFOAM Running, Solving & CFD | 1 | May 25, 2022 08:44 |
how to set periodic boundary conditions | Ganesh | FLUENT | 15 | November 18, 2020 06:09 |
[General] Slice origin as annotation in animation | bozack | ParaView | 6 | July 27, 2018 04:37 |
Equation for a rotating circle outside the origin | mali28 | Main CFD Forum | 0 | November 14, 2014 06:38 |
Coordinate of axis origin | Tang | FLUENT | 0 | October 4, 2004 16:38 |