|
[Sponsors] |
December 16, 2009, 13:42 |
locationInMesh Error
|
#1 |
Member
James Baker
Join Date: Dec 2009
Posts: 35
Rep Power: 16 |
I am very new to openFoam and am just trying to get it running at this point. However, I keep getting the error:
Refinement phase ---------------- Point (-0.018 -0.018 -0.018) is not inside the mesh or on a face or edge. Bounding box of the mesh-0.254 -0.762 -0.762) (1.778 0.762 0.762) From function refinementParameters::findCells(const polyMesh&) const in file autoHexMesh/autoHexMeshDriver/refinementParameters/refinementParameters.C at line 104. FOAM exiting . No matter if I choose a point inside the stl or outside (still within the bounding box) I get the same error. Any help is appreciated. here is my setup which clearly shows the surface within the bounding box. |
|
December 16, 2009, 13:49 |
|
#2 |
Senior Member
Anonymous
Join Date: Mar 2009
Posts: 110
Rep Power: 17 |
Have a look here:
http://www.cfd-online.com/Forums/ope...-mesh-but.html I had the same issue and I finally resolved it by manipulating the order of my initial bounding box. Can't help you much more than that, I'm afraid. |
|
December 16, 2009, 14:34 |
|
#3 |
Member
James Baker
Join Date: Dec 2009
Posts: 35
Rep Power: 16 |
Worked great, thank you!
|
|
June 20, 2017, 14:30 |
same problem
|
#4 |
New Member
ABHINAVMOHAN
Join Date: Jun 2017
Posts: 16
Rep Power: 8 |
convertToMeters 1;
vertices ( (48 660 -2015) //0 (2000 660 -2015) //1 (2000 3000 -2015) //2 (48 3000 -2015) //3 (48 660 4000) //4 (2000 660 4000) //5 (2000 3000 4000) //6 (48 3000 4000) //7 ); blocks ( hex (0 1 2 3 4 5 6 7) (20 8 8) simpleGrading (1 1 1) ); edges ( ); boundary ( frontAndBack { type patch; faces ( (1 2 6 5) (0 4 7 3) ); } inlet { type patch; faces ( (4 5 6 7) ); } outlet { type patch; faces ( (0 3 2 1) ); } lowerWall { type wall; faces ( (0 1 5 4) ); } upperWall { type patch; faces ( (3 7 6 2) ); } ); bounding box.PNG bounding box2.PNG same problem can`t figure this out. even though my STL file is in the box |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[OpenFOAM.org] compile error in dynamicMesh and thermophysicalModels libraries | NickG | OpenFOAM Installation | 3 | December 30, 2019 00:21 |
[blockMesh] blockMesh with double grading. | spwater | OpenFOAM Meshing & Mesh Conversion | 92 | January 12, 2019 09:00 |
[swak4Foam] GroovyBC the dynamic cousin of funkySetFields that lives on the suburb of the mesh | gschaider | OpenFOAM Community Contributions | 300 | October 29, 2014 18:00 |
OpenFOAM without MPI | kokizzu | OpenFOAM Installation | 4 | May 26, 2014 09:17 |
DecomposePar links against liblamso0 with OpenMPI | jens_klostermann | OpenFOAM Bugs | 11 | June 28, 2007 17:51 |