CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > OpenFOAM > OpenFOAM Meshing & Mesh Conversion

[Other] Importing mesh for use with Ggi

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   November 24, 2008, 18:41
Default Importing mesh for use with Ggi
  #1
Senior Member
 
louisgag's Avatar
 
Louis Gagnon
Join Date: Mar 2009
Location: Stuttgart, Germany
Posts: 338
Rep Power: 18
louisgag is on a distinguished road
Send a message via ICQ to louisgag
Good evening,

I recently got the Ggi interface working on OF 1.5 and successfully ran prof. Jasak's mixer2d example which was posted in the forums.

However, I have been struggling to import a mesh made with Gmsh because gmsh will not let me have two patches at the same location. I thus tried to make a mesh where the "insideSlider" and "outsideSlider" patches were slightly offset and then use attachMesh or stitchMesh utilities but had no success so far. The slider patches remain detached.

I would appreciate if anyone could give me a hint.

Thanks,

-Louis



louisgag is offline   Reply With Quote

Old   November 29, 2008, 00:29
Default Bonjour Louis, You might wa
  #2
Senior Member
 
Martin Beaudoin
Join Date: Mar 2009
Posts: 332
Rep Power: 22
mbeaudoin will become famous soon enough
Bonjour Louis,

You might want to export your mesh as two separate meshes and try to combine them together with mergeMeshes.

If you want to use "insideSlider" and "outsideSlider" as GGI patches, you don't want to stitch them together; you need to keep them as two distinct patches.

Martin
mbeaudoin is offline   Reply With Quote

Old   November 29, 2008, 01:03
Default hi Louis, Can u post me the
  #3
Member
 
Mahendra
Join Date: Mar 2009
Location: Pune, Maharashtra, India
Posts: 65
Rep Power: 17
mahendra is on a distinguished road
hi Louis,

Can u post me the details, how u got the Ggi working in OpenFOAM 1.5. I tried a lot but it is not working with the mixed2D case by Prof. Jasak.

You can reach me at mahendra.wankhede@gmail.com

Regards,
Mahendra
mahendra is offline   Reply With Quote

Old   November 29, 2008, 13:42
Default Salut Martin, thank you for
  #4
Senior Member
 
louisgag's Avatar
 
Louis Gagnon
Join Date: Mar 2009
Location: Stuttgart, Germany
Posts: 338
Rep Power: 18
louisgag is on a distinguished road
Send a message via ICQ to louisgag
Salut Martin,

thank you for the suggestion! I will try it and post feedback here.

Mahendra, if you use this mixer2D example: http://www.cfd-online.com/cgi-bin/Op...0177#POST20177 with the compiled source of http://www.cfd-online.com/cgi-bin/Op...7020#POST27020
it should work. Note that you will need to change some values in controlDict and perhaps a few other files to make the tutorial compatible with 1.5.
Let me know how it goes! (Also, you will only be able to visualize results with paraview from OF 1.4)


regards,

-Louis
louisgag is offline   Reply With Quote

Old   January 7, 2009, 17:14
Default Hello again, I got a custom
  #5
Senior Member
 
louisgag's Avatar
 
Louis Gagnon
Join Date: Mar 2009
Location: Stuttgart, Germany
Posts: 338
Rep Power: 18
louisgag is on a distinguished road
Send a message via ICQ to louisgag
Hello again,

I got a custom made 2D mixer case to run in OF-1.5-dev using my meshes imported from gmsh! Visualization with the paraFoam (paraview 3.3) script also works perfectly.

Thank you again Martin, and thank you prof. Jasak for the dev. release!

regards,
-Louis
louisgag is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
[ICEM] Missing face critical error while importing icem mesh to fluent tuhin ANSYS Meshing & Geometry 4 March 12, 2018 09:20
[Other] Mesh Importing Problem cuteapathy ANSYS Meshing & Geometry 2 June 24, 2017 06:29
[Commercial meshers] Importing ICEM Multiregion Mesh In OpenFOAM Aditya Patil OpenFOAM Meshing & Mesh Conversion 1 May 8, 2017 22:33
Gambit problems Althea FLUENT 22 January 4, 2017 04:19
Mesh importing Anna Tian FLUENT 5 December 22, 2013 16:09


All times are GMT -4. The time now is 20:08.