[Technical] Salome + Gmsh or enGrid for OpenFOAM?

wwrfd · June 22, 2011, 10:27

Hi everyone,

I am supposed to make a study on OpenFoam using open-source geometry and meshing software, the studied geometry will be mainly composed of cylindrical shapes. Problem is I've tried many combinaisons between different software like SalomeMeca, Gmsh, enGrid and others and I still don't what could be the best solution between using:

SalomeMeca => Geometry + Mesh and use ideasUnvToFoam to convert the mesh to make the study

SalomeMeca =>Export Geometry STL and then mesh into enGrid or Gmsh and then convert the mesh with gmshToFoam.

I know it exists plenty of other ways to create geometries and meshs but I don't know what is the most appropriate.

I know this subject must have been already discussed about elsewhere and I'm sorry for that.

Thank you for your answers.

elvis · July 19, 2011, 09:15

Hello,

there is even a third way via pythonflu see link
http://pythonflu.wikidot.com/hybridflu

mentioned in this presentation is http://www.openfoamworkshop.org/6th_...ord_slides.pdf that pythonflu can be used to directly use salome-mesh without converting thru ideasUnvToFoam (that has some limitations and therefore was not a suitable way for Mr. Cliffords work)

wwrfd · July 21, 2011, 10:38

Ok thank you I will try to use it since I planned to make my geometry and mesh on Salome!

June 22, 2011, 10:27	Salome + Gmsh or enGrid for OpenFOAM?	#1
wwrfd New Member Robin Join Date: Mar 2011 Location: France Posts: 6 Rep Power: 15	Hi everyone, I am supposed to make a study on OpenFoam using open-source geometry and meshing software, the studied geometry will be mainly composed of cylindrical shapes. Problem is I've tried many combinaisons between different software like SalomeMeca, Gmsh, enGrid and others and I still don't what could be the best solution between using: SalomeMeca => Geometry + Mesh and use ideasUnvToFoam to convert the mesh to make the study SalomeMeca =>Export Geometry STL and then mesh into enGrid or Gmsh and then convert the mesh with gmshToFoam. I know it exists plenty of other ways to create geometries and meshs but I don't know what is the most appropriate. I know this subject must have been already discussed about elsewhere and I'm sorry for that. Thank you for your answers. Kummi likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Error Importing Surface Mesh from GMSH to EnGrid	eric.m.tridas	enGrid	5	October 4, 2021 03:17
Import this Gmsh .msh file to enGrid	ffan	enGrid	0	May 5, 2014 12:28
gmsh to Engrid	Gora1000	enGrid	0	August 12, 2013 04:08
CAD -> gMsh -> enGrid -> OpenFOAM Problem	AlGates	OpenFOAM	7	August 6, 2010 12:46
[Gmsh] Import problem	ARC	OpenFOAM Meshing & Mesh Conversion	0	February 27, 2010 10:56

July 19, 2011, 09:15		#2
elvis Senior Member Elvis Join Date: Mar 2009 Location: Sindelfingen, Germany Posts: 620 Blog Entries: 6 Rep Power: 24	Hello, there is even a third way via pythonflu see link http://pythonflu.wikidot.com/hybridflu mentioned in this presentation is http://www.openfoamworkshop.org/6th_...ord_slides.pdf that pythonflu can be used to directly use salome-mesh without converting thru ideasUnvToFoam (that has some limitations and therefore was not a suitable way for Mr. Cliffords work)

July 21, 2011, 10:38		#3
wwrfd New Member Robin Join Date: Mar 2011 Location: France Posts: 6 Rep Power: 15	Ok thank you I will try to use it since I planned to make my geometry and mesh on Salome!