CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > OpenFOAM > OpenFOAM Meshing & Mesh Conversion

[snappyHexMesh] Surface Meshes Merged in SnappyHexMesh (Pictures Inlcuded)

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   December 3, 2012, 05:33
Default Surface Meshes Merged in SnappyHexMesh (Pictures Inlcuded)
  #1
sda
New Member
 
Join Date: Apr 2010
Posts: 16
Rep Power: 15
sda is on a distinguished road
Dear OpeFOAMers,

I am working on a mesh of a generic car body using SnappyHexMesh. There is a region where the surface mesh on two tyres merges witht the wheel wheel of the car body itself.

I am reasonably certain that the .STL file is of good quality so I don't think the geometry is the problem.

I am steadily working my way through the meshing parameters to see which one will effect and improvement but I was hoping to reach that goal sooner with a tip from one of you.

I have included pictures.

Thanks for any suggestions.

Regards,


Saif
Attached Images
File Type: jpg car1.jpg (84.7 KB, 73 views)
File Type: jpg car2.jpg (93.5 KB, 66 views)
File Type: jpg tyre1.jpg (96.9 KB, 70 views)
File Type: jpg tyre2.jpg (97.7 KB, 57 views)
sda is offline   Reply With Quote

Old   December 3, 2012, 09:08
Default
  #2
Senior Member
 
sail's Avatar
 
Vieri Abolaffio
Join Date: Jul 2010
Location: Always on the move.
Posts: 308
Rep Power: 15
sail is on a distinguished road
the problem is that you just have one cell between the tyre and the body and sHM doesn't know how to solve it. increase your mesh resolution in that area to have at least 3 cells between the two surfaces and the issue will disappear. although to have good results you'll probably need more than that---
__________________
http://www.leadingedge.it/
Naval architecture and CFD consultancy
sail is offline   Reply With Quote

Old   December 3, 2012, 09:22
Default
  #3
sda
New Member
 
Join Date: Apr 2010
Posts: 16
Rep Power: 15
sda is on a distinguished road
Vieri,

Thanks for your reply. Do I simply increase the refinement on the surfaces or do I increase the values for any of the following parameters below

nCellsBetweenLevels 3;

tolerance 4.0; // under the snapControls

Thanks.

Saif
sda is offline   Reply With Quote

Old   December 3, 2012, 13:01
Default
  #4
sda
New Member
 
Join Date: Apr 2010
Posts: 16
Rep Power: 15
sda is on a distinguished road
Vieri,

Your suggestion was useful but not in the way I expected. I checked the geometry because of your comment and found that a designer had actually moved the wheel. It was touching the wheel arch surface.

After I moved the wheel to the correct position it meshes fine now.

Thanks all the same.

Regards,


Saf
sda is offline   Reply With Quote

Reply

Tags
snappyhexmesh 3d, surface mesh merged

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
[snappyHexMesh] snappyHexMesh can't create refimenet region clktp OpenFOAM Meshing & Mesh Conversion 3 February 27, 2022 09:26
[snappyHexMesh] snappyHexMesh surface refinement bugs wc34071209 OpenFOAM Meshing & Mesh Conversion 9 October 7, 2018 06:53
[snappyHexMesh] How to create internal boundaries using snappyHexMesh robyTKD OpenFOAM Meshing & Mesh Conversion 2 October 19, 2014 09:57
Cluster ID's not contiguous in compute-nodes domain. ??? Shogan FLUENT 1 May 28, 2014 15:03
[snappyHexMesh] snappyHexMesh aborting Tobi OpenFOAM Meshing & Mesh Conversion 0 November 10, 2010 03:23


All times are GMT -4. The time now is 18:57.