[snappyHexMesh] Snappy Hex Mesh External Domain

willindsey · June 9, 2017, 01:46

I am trying to mesh a NACA airfoil and simulate an external flow. I am using snappy hex mesh to mesh the airfoil, but when I run snappy hex mesh the external domain disappears. All that remains is a meshed airfoil. I have tried two methods. The first is just inserting the NACA airfoil into the blockMesh domain. The second is inserting the an external volume with the surface mesh of the airfoil inside. I run the snappy hex mesh with out any errors output. I then look at the mesh in paraFoam, but the external volume on time step 1 and 2 is gone, the only patch there is the airfoil. Any advice would be helpful. Thanks

Dipsomaniac · June 9, 2017, 02:28

Hi Wil

In your snappyHexMeshDict file, make sure that the locationInMesh coordinates are outside the STL used to mesh the aerofoil. It sounds like you may have chosen a point inside the STL, hence it is only meshing the inside of the aerofoil as opposed to the exterior.

Brian

willindsey · June 9, 2017, 22:03

Thats it. All of the tutorials I found online said to put the location inside the mesh, but they were all for internal flows. Thanks

June 9, 2017, 01:46	Snappy Hex Mesh External Domain	#1
willindsey New Member wil Join Date: Oct 2016 Posts: 6 Rep Power: 9	I am trying to mesh a NACA airfoil and simulate an external flow. I am using snappy hex mesh to mesh the airfoil, but when I run snappy hex mesh the external domain disappears. All that remains is a meshed airfoil. I have tried two methods. The first is just inserting the NACA airfoil into the blockMesh domain. The second is inserting the an external volume with the surface mesh of the airfoil inside. I run the snappy hex mesh with out any errors output. I then look at the mesh in paraFoam, but the external volume on time step 1 and 2 is gone, the only patch there is the airfoil. Any advice would be helpful. Thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[blockMesh] FATAL ERROR: face 6 in patch 2 does not have neighbour cell face: 4(8 9 21 20)	robingilbert	OpenFOAM Meshing & Mesh Conversion	28	November 23, 2023 06:32
[snappyHexMesh] Snappy Hex Mesh - issue with smoothness of the model edges	olek.warc	OpenFOAM Meshing & Mesh Conversion	1	August 31, 2018 11:31
[snappyHexMesh] Scaling issues with STL file and snappy hex mesh .	pradyumnsingh	OpenFOAM Meshing & Mesh Conversion	2	July 18, 2018 16:17
Importing snappy hex mesh to fsiFoam	Mohammad Jam	OpenFOAM Running, Solving & CFD	0	January 28, 2017 19:28
Out File does not show Imbalance in %	Mmaragann	CFX	5	January 20, 2017 10:20

June 9, 2017, 02:28		#2
Dipsomaniac Member Brian Willis Join Date: Mar 2011 Location: Cape Town, South Africa Posts: 58 Rep Power: 15	Hi Wil In your snappyHexMeshDict file, make sure that the locationInMesh coordinates are outside the STL used to mesh the aerofoil. It sounds like you may have chosen a point inside the STL, hence it is only meshing the inside of the aerofoil as opposed to the exterior. Brian

June 9, 2017, 22:03		#3
willindsey New Member wil Join Date: Oct 2016 Posts: 6 Rep Power: 9	Thats it. All of the tutorials I found online said to put the location inside the mesh, but they were all for internal flows. Thanks