[snappyHexMesh] internal mesh with snappyHexMesh

romant · August 11, 2009, 03:42

Hej,

I was wondering if it is possible to mesh the inside of a body with snappyHexMesh. The problem is fairly simple. I have a cup of a complex shape (meshing the surface with snappyHex is no problem) and a body of water inside (also of this complex shape). I try to mesh the body of water from the inside, it removes the bounding box around the body of water, which I think is a first success, but when I load the body of water into paraView with paraFoam I can't see that there are cells inside the body. snappyHexMesh seems to only model the wall of the body. How can I make it create a mesh not only on the wall, but also in the center.

Could it be that paraView just does not show the inside mesh of the body?

mattijs · August 11, 2009, 04:24

snappyHexMesh refines an existing mesh and uses a walk (cell to face to cell etc) from the locationInMesh to find out which cells are connected. Anything else gets removed. Sometimes if your surfaces are not closed the mesh will spill out.

romant · August 11, 2009, 05:12

Thank you...

The problem were not any open geometries. I already found now that paraView only shows the surface mesh and upon zooming still only shows the surface mesh. When creating a slice of the geometry, the internal cells show. So my mesh was right all along, but I could not see it.

August 11, 2009, 03:42	internal mesh with snappyHexMesh	#1
romant Senior Member Roman Thiele Join Date: Aug 2009 Location: Eindhoven, NL Posts: 374 Rep Power: 20	Hej, I was wondering if it is possible to mesh the inside of a body with snappyHexMesh. The problem is fairly simple. I have a cup of a complex shape (meshing the surface with snappyHex is no problem) and a body of water inside (also of this complex shape). I try to mesh the body of water from the inside, it removes the bounding box around the body of water, which I think is a first success, but when I load the body of water into paraView with paraFoam I can't see that there are cells inside the body. snappyHexMesh seems to only model the wall of the body. How can I make it create a mesh not only on the wall, but also in the center. Could it be that paraView just does not show the inside mesh of the body?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
y+ = 1 boundary layer mesh with snappyHexMesh	Arzed23	OpenFOAM Running, Solving & CFD	6	November 23, 2022 15:15
[snappyHexMesh] Add Mesh Layers doesnt work on the whole surface	Kryo	OpenFOAM Meshing & Mesh Conversion	13	February 17, 2022 07:34
[mesh manipulation] Importing Multiple Meshes	thomasnwalshiii	OpenFOAM Meshing & Mesh Conversion	18	December 19, 2015 18:57
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 11:55
Icemcfd 11: Loss of mesh from surface mesh option?	Joe	CFX	2	March 26, 2007 18:10

August 11, 2009, 04:24		#2
mattijs Senior Member Mattijs Janssens Join Date: Mar 2009 Posts: 1,419 Rep Power: 26	snappyHexMesh refines an existing mesh and uses a walk (cell to face to cell etc) from the locationInMesh to find out which cells are connected. Anything else gets removed. Sometimes if your surfaces are not closed the mesh will spill out.

August 11, 2009, 05:12		#3
romant Senior Member Roman Thiele Join Date: Aug 2009 Location: Eindhoven, NL Posts: 374 Rep Power: 20	Thank you... The problem were not any open geometries. I already found now that paraView only shows the surface mesh and upon zooming still only shows the surface mesh. When creating a slice of the geometry, the internal cells show. So my mesh was right all along, but I could not see it.