Calculation of yPlus in MRF simulations

MatejAndrej · February 17, 2015, 04:27

Dear All,

I'm simulating airflow passing a propeller using MRF. I'm using incompressible solver simpleFoam and kOmegaSST turbulence model with nutkWallFunction as a wall function at nut. I don't have problems with simulations, it converges beautifully to nice results, but I would like to ask how do I calculate yPlus in my situation?

Since it is High-Re type of simulation I ran yPlusRAS utility, but resulting yPlus is not ok even though I recalculated U by adding \omega x R (rotating term).

After a little bit of research in doxygen I found that since I'm using nutkWallFunction the utility yPlusRAS consequently uses equations: u_{\tau}=C_{\mu}^{1/4}\sqrt{k} together with y+ definition y+=y u_{tau}/\nu. Since turbulent kinetic energy k is being calculated in rotating frame of reference it apparently doesn't result in correct y+ calculation?!?

Then I changed kOmegaSST in constant/RASProperties to SpalartAllmaras and I changed all nutkWallFunction in nut file to nutUWallFunction in the last simulation time folder. Then I ran yPlusRAS again and this time it calculated "logical" y+ distribution.

nutUWallFunction uses an iterative calculation in order to calculate y+ described in: http://www.cfd-online.com/Wiki/Two_equation_models (standard wall function).

Since I ran simulation with nutkWallFunction and calculated yPlus with nutUWallFunction I don't know what to think about these results?!?

How do you calculate yPlus in MRF?

Thank you very much for your help.

Best
Matej

be_inspired · April 28, 2015, 12:01

Dear MatejAndrej,

Excuse for using this same topic but I think you can help me the little I need.
I am trying to use the same approach that yours to simulate a wind turbine using MRF approach. All goes ok until I activate turbulence ( I am trying to detect where the problem is).
For the walls inside the rotating region I have put nutkWallFunction, KqRWallFunction and epsilonWallFunction.
I have also tried nutUSpaldingWallFunction with no luck

Is it needed to change in some way the wall function for MRF? The k and epsilon values at wall increase a lot and then the simulation crash.

I am using OF2.3.x and kEpsilon model ( the mesh is ready for y+ around 100)

February 17, 2015, 04:27	Calculation of yPlus in MRF simulations	#1
MatejAndrej New Member Matej Andrejasic Join Date: Sep 2010 Posts: 2 Rep Power: 0	Dear All, I'm simulating airflow passing a propeller using MRF. I'm using incompressible solver simpleFoam and kOmegaSST turbulence model with nutkWallFunction as a wall function at nut. I don't have problems with simulations, it converges beautifully to nice results, but I would like to ask how do I calculate yPlus in my situation? Since it is High-Re type of simulation I ran yPlusRAS utility, but resulting yPlus is not ok even though I recalculated U by adding \omega x R (rotating term). After a little bit of research in doxygen I found that since I'm using nutkWallFunction the utility yPlusRAS consequently uses equations: u_{\tau}=C_{\mu}^{1/4}\sqrt{k} together with y+ definition y+=y u_{tau}/\nu. Since turbulent kinetic energy k is being calculated in rotating frame of reference it apparently doesn't result in correct y+ calculation?!? Then I changed kOmegaSST in constant/RASProperties to SpalartAllmaras and I changed all nutkWallFunction in nut file to nutUWallFunction in the last simulation time folder. Then I ran yPlusRAS again and this time it calculated "logical" y+ distribution. nutUWallFunction uses an iterative calculation in order to calculate y+ described in: http://www.cfd-online.com/Wiki/Two_equation_models (standard wall function). Since I ran simulation with nutkWallFunction and calculated yPlus with nutUWallFunction I don't know what to think about these results?!? How do you calculate yPlus in MRF? Thank you very much for your help. Best Matej

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] Contribution a new utility: refine wall layer mesh based on yPlus field	lakeat	OpenFOAM Community Contributions	58	December 23, 2021 02:36
Solver Yplus of Automatic wall treatment	justjhy	CFX	2	May 4, 2013 07:19
Wrong calculation of yPlus for low-Re models	bastil	OpenFOAM Bugs	4	February 9, 2010 07:39
which yplus (SST)	sanchezz	CFX	17	January 11, 2010 04:45
DIVERGENCE with MRF calculation in FLUENT	FLUENT USER	Main CFD Forum	3	June 28, 1999 15:44

April 28, 2015, 12:01		#2
be_inspired Senior Member M. Montero Join Date: Mar 2009 Location: Madrid Posts: 153 Rep Power: 17	Dear MatejAndrej, Excuse for using this same topic but I think you can help me the little I need. I am trying to use the same approach that yours to simulate a wind turbine using MRF approach. All goes ok until I activate turbulence ( I am trying to detect where the problem is). For the walls inside the rotating region I have put nutkWallFunction, KqRWallFunction and epsilonWallFunction. I have also tried nutUSpaldingWallFunction with no luck Is it needed to change in some way the wall function for MRF? The k and epsilon values at wall increase a lot and then the simulation crash. I am using OF2.3.x and kEpsilon model ( the mesh is ready for y+ around 100)