wallHeatFlux utility and chtMultiRegionFoam solver

Lada · October 5, 2011, 06:29

I have run into problem using wallHeatFlux utility to obtain patches heat fluxes when applied to chtMultiRegionFoam solver. The message I am getting is:

--> FOAM FATAL IO ERROR:
cannot find file

file: /home/lada/OpenFOAM/lada-2.0.0/run/BALKON/balkon_svisle_1/constant/thermophysicalProperties at line 0.

From function regIOobject::readStream()
in file db/regIOobject/regIOobjectRead.C at line 73.

Is there any way to solve this problem except for writing my own wallHeatFlux utility?

Tuxeedo · June 7, 2012, 08:10

Hey Vladimir,
did you find a Solution to your problem?

Lada · June 7, 2012, 08:50

I had to modify patchIntegrate or patchAverage or combine both of them to define a utility that would give me the heat fluxes. My model was a rather simple one (essentially heat conduction only) consisting of multiple solids with defined heat transfer coefficient and temperature at the outer surface.
And I wasn't able to get the fluxes via the wallHeatFlux utility.

Tuxeedo · June 7, 2012, 09:02

Thanks for your Reply.
Unfortunately i'm stuck on a coorporate installation where compiling self made tools is an enormous hassle.
I am surprised, that it is difficult to obtain wall heat Flux in a very simple incompressible steady state fluid solid system...

Lada · June 7, 2012, 09:46

Sadly, I'm not too skilled at modifying or writing my own codes as that one was my first one. I have slightly diverted my attention off the openFoam. I've tried looking up whether wallHeatFlux is applied within tutorials but no success. I'm sorry but I can't help you much.
I suppose asking you 'have you searched the forum here for anything related to your application' is rather silly.

October 5, 2011, 06:29	wallHeatFlux utility and chtMultiRegionFoam solver	#1
Lada New Member vladimir krejci Join Date: Mar 2009 Location: Czech Republic Posts: 20 Rep Power: 17	I have run into problem using wallHeatFlux utility to obtain patches heat fluxes when applied to chtMultiRegionFoam solver. The message I am getting is: --> FOAM FATAL IO ERROR: cannot find file file: /home/lada/OpenFOAM/lada-2.0.0/run/BALKON/balkon_svisle_1/constant/thermophysicalProperties at line 0. From function regIOobject::readStream() in file db/regIOobject/regIOobjectRead.C at line 73. Is there any way to solve this problem except for writing my own wallHeatFlux utility?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problem with running chtMultiRegionFoam after using setSet utility	Victor	OpenFOAM	12	March 24, 2023 00:01
Is the sample utility compatible with chtMultiRegionFoam	mirko	OpenFOAM Post-Processing	4	February 15, 2016 07:28

June 7, 2012, 08:10		#2
Tuxeedo New Member Hauke Join Date: Jun 2012 Posts: 5 Rep Power: 13	Hey Vladimir, did you find a Solution to your problem?

June 7, 2012, 08:50		#3
Lada New Member vladimir krejci Join Date: Mar 2009 Location: Czech Republic Posts: 20 Rep Power: 17	I had to modify patchIntegrate or patchAverage or combine both of them to define a utility that would give me the heat fluxes. My model was a rather simple one (essentially heat conduction only) consisting of multiple solids with defined heat transfer coefficient and temperature at the outer surface. And I wasn't able to get the fluxes via the wallHeatFlux utility.

June 7, 2012, 09:02		#4
Tuxeedo New Member Hauke Join Date: Jun 2012 Posts: 5 Rep Power: 13	Thanks for your Reply. Unfortunately i'm stuck on a coorporate installation where compiling self made tools is an enormous hassle. I am surprised, that it is difficult to obtain wall heat Flux in a very simple incompressible steady state fluid solid system...

June 7, 2012, 09:46		#5
Lada New Member vladimir krejci Join Date: Mar 2009 Location: Czech Republic Posts: 20 Rep Power: 17	Sadly, I'm not too skilled at modifying or writing my own codes as that one was my first one. I have slightly diverted my attention off the openFoam. I've tried looking up whether wallHeatFlux is applied within tutorials but no success. I'm sorry but I can't help you much. I suppose asking you 'have you searched the forum here for anything related to your application' is rather silly.