Hi, at first sorry for my b
 

Hi,

at first sorry for my bad english...

However, I want to use OpenFOAM for simulation. I am engineer for HVAC and I am to interesset in simulation for airflows in building rooms but my experiment crashed in OpenFOAM everytime :-(

I make a room with one block and every side is a wall function. Furthermore I make two blocks on the side of a wall. One block is for the inlet slot and the other for the outlet slot. My question is: When I make the block for inlet slot I am defining one patch of the block as the inlet patch and the other 5 side are walls? If am not defining the other side, the simulation stops because of "empty patches".

Maybe can somebody give me excample for simulation inlet slot in 3D rooms? It whould help me.

Thanks
Myting

Hi Myting Post the case or
 

Hi Myting

Post the case or send it to me by email and i will have a look, i think the geometry is somehow wrong

atzaru@gmail.com


atzaru

Hi Myting, Please post you
 

Hi Myting,

Please post your case or send it to me by email and i will have a look

atzaru at gmail.com

Atzaru

Hi, my case: /*---------
 

Hi,

my case:

/*---------------------------------------------------------------------------*\
| ========= | |
| \ / F ield | OpenFOAM: The Open Source CFD Toolbox |
| \ / O peration | Version: 1.3 |
| \ / A nd | Web: http://www.openfoam.org |
| \/ M anipulation | |
\*---------------------------------------------------------------------------*/

// FoamX Case Dictionary.

FoamFile
{
version 2.0;
format ascii;

root "/home/cfd1/OpenFOAM/cfd1-1.3/run/tutorials/buoyantSimpleFoam";
case "office";
instance "constant/polyMesh";
local "";

class dictionary;
object blockMeshDict;
}

// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //

arguments "/home/cfd1/OpenFOAM/cfd1-1.3/run/tutorials/buoyantSimpleFoam/office" off;

convertToMeters 1;

vertices
(
(0 0 0)
(10 0 0)
(10 5 0)
(0 5 0)
(0 0 10)
(10 0 10)
(10 5 10)
(0 5 10)
(2 4 0)
(3 4 0)
(3 4.2 0)
(2 4.2 0)
(2 4 0.1)
(3 4 0.1)
(3 4.2 0.1)
(2 4.2 0.1)
(7 4 0)
(8 4 0)
(8 4.2 0)
(7 4.2 0)
(7 4 0.1)
(8 4 0.1)
(8 4.2 0.1)
(7 4.2 0.1)
);

blocks
(
hex (0 1 2 3 4 5 6 7) (40 40 40) simpleGrading (1 1 1)
hex (8 9 10 11 12 13 14 15) (20 20 20) simpleGrading (1 1 1)
hex (16 17 18 19 20 21 22 23) (20 20 20) simpleGrading (1 1 1)
);

edges
(
);

patches
(
wall floor
(
(1 5 4 0)
)
wall ceiling
(
(3 7 6 2)
)
wall fixedWalls
(
(0 4 7 3)
(2 6 5 1)
(0 3 2 1)
(4 5 6 7)
)
patch inlet
(
(12 13 14 15)
)
patch fixedWallsInlet
(
(8 11 10 9)
(9 10 14 13)
(15 11 8 12)
(14 10 11 15)
(13 12 8 9)
)
patch Outlet
(
(20 21 22 23)
)
patch fixedWallsOutlet
(
(16 19 18 17)
(17 18 22 21)
(23 19 16 20)
(22 18 19 23)
(17 21 20 16)
)
);

mergePatchPairs
(
);


// ************************************************** *********************** //

1- Actually it seems to me you
 

1- Actually it seems to me you describe in a wrong way your geometry. First u make a room (the first block). After that u make two separate blocks for inlet and outlet. The inlet-outlet ports should be located on the face of the first block (patches).

2- As a general rule the blocks should share common faces, yours are not connected what so ever


adi

Hi, thanks for you answer.
 

Hi,

thanks for you answer. Can you give me an example? It whould be nice for me.

So, I don't need the other blocks for Inlet and Outletslot? It is easier to make only a patch (face) on one site of the roomwall?
How can I connected the block with each other? I thought the Mesher do this kind of job???

Thank you
Myting

ok i have a small tutorial
 

ok

i have a small tutorial with some cases i presented in our department... i will post them today or tomorrow

adrian

Hi You can download the tut
 

Hi

You can download the tutorial here

http://www.schunternet.de/~amagda/cf...M_tutorial.odt

Any comments, corrections, new cases will be welcome, i am sure it can be made a lot better.

Adi

Thank you very much for your h
 

Thank you very much for your help...

Myting

Hi Adrian, I think, the las
 

Hi Adrian,

I think, the last case in your tutorial is not complete. The "blockMeshDict" has not enough vertex to make all blocks? Can you check your file please? Thank you very much...

Myting

Yup i just corrected ad
 

Yup

i just corrected

adi

Hi Adrian, I tried your las
 

Hi Adrian,

I tried your last case but it is impossible. I don't know why, but I got "nan" in solution always. Can you send me your full case files?

Thank you.
Myting