chtMultiRegionFoam, conduction with a contact resistance between two solids

romain.h · September 16, 2012, 18:45

Hello,
I have a simple test case with 3 solid, and I am trying to solve a simple heat conduction inside those three solids. The third solid should not have any influence for now (see figure)

If I use

Code:

type            compressible::turbulentTemperatureCoupledBaffleMixed;
        value           uniform 300;
        neighbourFieldName T;
        K               solidThermo;
        KName           none;

as in the tutorial, it's working, I have a gradient of DT=q*Rth.

My problem is to introduce an additional resistance, for example a contact resistance between two solids.
I was planning on using the boundary condition fixedGradient, but I have an error when I tried to use such a boundary condition between two solids.

Code:

Attempt to cast type fixedGradient to type compressible::turbulentTemperatureCoupledBaffleMixed

Any idea how I can solve my problem ?

Thanks in advance for your help,
Romain

pangelo · October 8, 2013, 02:25

Hi,
I am a newbie in OF and I am also facing a problem similar to the one Romain posted.
My question: is it possible to set a contact resistance between two solids? (I am using the chtMultiRegionSimpleFoam solver).
Thank you in advance for your answer.

Ciao.

September 16, 2012, 18:45	chtMultiRegionFoam, conduction with a contact resistance between two solids	#1
romain.h New Member Romain Join Date: Aug 2012 Posts: 12 Rep Power: 15	Hello, I have a simple test case with 3 solid, and I am trying to solve a simple heat conduction inside those three solids. The third solid should not have any influence for now (see figure) If I use Code: type compressible::turbulentTemperatureCoupledBaffleMixed; value uniform 300; neighbourFieldName T; K solidThermo; KName none; as in the tutorial, it's working, I have a gradient of DT=q*Rth. My problem is to introduce an additional resistance, for example a contact resistance between two solids. I was planning on using the boundary condition fixedGradient, but I have an error when I tried to use such a boundary condition between two solids. Code: Attempt to cast type fixedGradient to type compressible::turbulentTemperatureCoupledBaffleMixed Any idea how I can solve my problem ? Thanks in advance for your help, Romain

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
contact resistance in flotherm	Sivan_nk	FloEFD, FloWorks & FloTHERM	3	January 14, 2014 00:06
how to use contact resistance model in floEFD	eggliang	FloEFD, FloWorks & FloTHERM	4	August 5, 2011 01:36
Variable Thermal Contact Resistance	octavyo	CFX	3	March 13, 2011 12:11
handle thin material or thermal contact resistance	sven82	OpenFOAM	3	February 21, 2011 08:43
conduction between 2 different solids	matt	FLUENT	5	November 9, 2006 09:57

October 8, 2013, 02:25		#2
pangelo New Member Join Date: Sep 2013 Posts: 3 Rep Power: 14	Hi, I am a newbie in OF and I am also facing a problem similar to the one Romain posted. My question: is it possible to set a contact resistance between two solids? (I am using the chtMultiRegionSimpleFoam solver). Thank you in advance for your answer. Ciao.