Problem edcSimpleFoam (combustion)

rafi525 · April 27, 2013, 08:40

Hello,

I'm using OF-1.7 with Dominik Christ's solver for EDC model with detailed kinetics.
I'm simulating a jet in hot coflow and I have 3 inlets in my domain : fuel (CH4/H2), coflow (products of CH4/H2 previous combustion) and air (O2,N2). The inlet of fuel is along the axis of the burner, the coflow is up of fuel and air is up of coflow.
My problem is that the solver works for small kinetic mechanisms (1 step, 2 steps or 4 steps) but doesn't with detailed ones (KEE, GRI-3.0). What I do is stating the complex mechanisms simulation with the 1 step solution but the flame blows out and moreover I have a new combustion zone appearing in the air region although there is no fuel there.

Can anyone help?

Screenshot-1.jpg

grk34 · April 28, 2013, 09:00

hi rafi,

i am a newbie to openfoam.

I am trying to simulate the same case and just replicate the tutorial. How to run the simualtion. I am using openfoam2.2.0. what should i type in the command window?

i typed edcSimpleFoam. it doesnt work...

Thanks
Vivek

rafi525 · April 28, 2013, 14:34

Hi vivek,

this solver only works on OF-1.7 (for the moment) unless you are able to adapt it for 2.x.
if the tutorial works for you with detailed chemistry (GRI-3.0) let me know it please.

Regards

grk34 · April 28, 2013, 21:32

Thank you rafi! I will try to use older versions.

Will OpenFoam version 2.2.0 s reactingFOAM suit your application?

umatari · May 15, 2013, 03:05

Hey, is anyone interested in adapting edcSimpleFoam for 2.2?
I'll give it a try, but I'm far from being experienced and wondered if someone would give it a shot too, maybe in close collaboration...

PeterBishop · October 21, 2013, 04:44

Quote:

Originally Posted by umatari

Hey, is anyone interested in adapting edcSimpleFoam for 2.2?
I'll give it a try, but I'm far from being experienced and wondered if someone would give it a shot too, maybe in close collaboration...

Hi,
any news?

April 27, 2013, 08:40	Problem edcSimpleFoam (combustion)	#1
rafi525 New Member Join Date: Apr 2013 Posts: 2 Rep Power: 0	Hello, I'm using OF-1.7 with Dominik Christ's solver for EDC model with detailed kinetics. I'm simulating a jet in hot coflow and I have 3 inlets in my domain : fuel (CH4/H2), coflow (products of CH4/H2 previous combustion) and air (O2,N2). The inlet of fuel is along the axis of the burner, the coflow is up of fuel and air is up of coflow. My problem is that the solver works for small kinetic mechanisms (1 step, 2 steps or 4 steps) but doesn't with detailed ones (KEE, GRI-3.0). What I do is stating the complex mechanisms simulation with the 1 step solution but the flame blows out and moreover I have a new combustion zone appearing in the air region although there is no fuel there. Can anyone help? Screenshot-1.jpg Last edited by rafi525; April 30, 2013 at 05:14.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
hel (turbulent viscosity ratio limited) for supersonic combustion problem	omar.2002bh	FLUENT	2	September 5, 2012 11:04
Problem using EDM for combustion	nakul	FLUENT	1	August 11, 2011 05:01
A problem with combustion	Luk	Main CFD Forum	1	April 28, 2008 09:55
Strange problem with combustion	Luk	CFX	1	April 28, 2008 09:54
Combustion problem	rupal	CFX	0	April 21, 2008 05:29

April 28, 2013, 09:00		#2
grk34 New Member Vivek Join Date: Apr 2013 Posts: 9 Rep Power: 13	hi rafi, i am a newbie to openfoam. I am trying to simulate the same case and just replicate the tutorial. How to run the simualtion. I am using openfoam2.2.0. what should i type in the command window? i typed edcSimpleFoam. it doesnt work... Thanks Vivek

April 28, 2013, 14:34		#3
rafi525 New Member Join Date: Apr 2013 Posts: 2 Rep Power: 0	Hi vivek, this solver only works on OF-1.7 (for the moment) unless you are able to adapt it for 2.x. if the tutorial works for you with detailed chemistry (GRI-3.0) let me know it please. Regards

April 28, 2013, 21:32		#4
grk34 New Member Vivek Join Date: Apr 2013 Posts: 9 Rep Power: 13	Thank you rafi! I will try to use older versions. Will OpenFoam version 2.2.0 s reactingFOAM suit your application?

May 15, 2013, 03:05		#5
umatari New Member Join Date: Apr 2013 Posts: 1 Rep Power: 0	Hey, is anyone interested in adapting edcSimpleFoam for 2.2? I'll give it a try, but I'm far from being experienced and wondered if someone would give it a shot too, maybe in close collaboration...