DamBreak tutorial in 3D

Kahnbein.Kai · October 25, 2020, 02:16

Hello,

i modified the DamBreak 2D tutorial, an add the third generation. The position of the alpha.phase 1 column i changed also. Here is a picture with three views at the timestep 0.

https://www.imagebanana.com/s/1919/lHbZccfd.html
And here at the timestep 399 (4 sec)
https://www.imagebanana.com/s/1919/Qb68DaA8.html

Why is the "water" collected at the edge of the x axis ? I dont changed the g file the value of the gravity is still 0 -9.81 0.

Usually the water should distribute at the x axis and y axis face ?

Best regards
Kai

Kahnbein.Kai · November 1, 2020, 10:12

Hello, nobody post a reply

. So i think i have to load up the 0-, Constant- and the Systemfolder. Here is the link: https://we.tl/t-5LygYUke0n Is there anything wrong in my setup ? Best regards Kai

guin · November 1, 2020, 13:16

I didn't download your setup, but I'd suggest you to check whether your case is still using empty boundary conditions for the front and back patches.

Kahnbein.Kai · November 2, 2020, 11:52

Hey guin,
thank you for your reply.

Yes, both of them are empty. In Paraview they are called defaultFaces.
I will try to set a wall boundary aswell and run the case again.

Best regards

Kai

by the way: i have an offtopic question. How you find the right vertices, faces and so on for the blockMeshDict File. I can open the geometry in Paraview, but i dont find a way to display the vertices or face numbers.

guin · November 2, 2020, 11:55

Quote:

Originally Posted by Kahnbein.Kai

by the way: i have an offtopic question. How you find the right vertices, faces and so on for the blockMeshDict File. I can open the geometry in Paraview, but i dont find a way to display the vertices or face numbers.

try

Code:

paraFoam -block

Kahnbein.Kai · November 2, 2020, 12:10

I got this message:

Code:

kai@Kai-Desktop:~/OpenFOAM/kai-7/run/tutorials_of/multiphase/interFoam/laminar/damBreak/damBreak$ paraFoam -block FATAL ERROR: The official reader module for OpenFOAM data does not exist on your system.  This means that the version of ParaView you are using was not compiled with OpenFOAM, or distributed with a packaged version of OpenFOAM.  For information on packaged versions of OpenFOAM/ParaView and compilation of OpenFOAM/ParaView, see https://openfoam.org/download  Alternatively, you might be able to view your OpenFOAM data with the reader module provided with ParaView by running:     paraFoam -builtin

Is there any way to do it with paraview 5.8.1 ? Best regards Kai

guin · November 3, 2020, 05:36

Quote:

Originally Posted by Kahnbein.Kai

I got this message:

Code:

kai@Kai-Desktop:~/OpenFOAM/kai-7/run/tutorials_of/multiphase/interFoam/laminar/damBreak/damBreak$ paraFoam -block FATAL ERROR: The official reader module for OpenFOAM data does not exist on your system.  This means that the version of ParaView you are using was not compiled with OpenFOAM, or distributed with a packaged version of OpenFOAM.  For information on packaged versions of OpenFOAM/ParaView and compilation of OpenFOAM/ParaView, see https://openfoam.org/download  Alternatively, you might be able to view your OpenFOAM data with the reader module provided with ParaView by running:     paraFoam -builtin

Is there any way to do it with paraview 5.8.1 ? Best regards Kai

You can either go again over the installation of the ParaView version that comes along with OpenFOAM (*) or take a look here for other alternatives:
https://openfoamwiki.net/index.php/B..._blockMeshDict

(*) It seems to me, you are working with OpenFOAM-7, so look for your relevant scenario:
https://openfoam.org/download/7-source/
https://openfoam.org/download/7-macos/
https://openfoam.org/download/7-linux/
https://openfoam.org/download/7-ubuntu/

Kahnbein.Kai · November 3, 2020, 09:58

Hey guin,

thank you, for your detailed answer. I tried to reinstall openfoam 7 with the code

Code:

sudo apt-get -y install openfoam7

but it dosent install paraview 5.6.0 again ;(

At the begin of the page for ubuntu you mentioned is the name of the paraview pack written down. So i tried

Code:

sudo apt-get -y isntall paraviewopenfoam56

And it works, perfektly

Thank you very much for your help !

https://s1.imagebanana.com/file/201103/p3qpWEvC.png

Best regards
Kai

ps: so i will look at the emtpy patches

Kahnbein.Kai · November 14, 2020, 02:11

Hey guin, yes you are right, i changed the patches (front- and backwall) from "empty" to "wall". In the new run the water distributes "right" on the floor. But why does have the patches so much influence to the alpha1 phase ? What is different in these two simulations ? Best regards Kai

Yann · November 15, 2020, 12:49

Hi Kai,

The empty type is meant to be used on 2D cases.
Have a look at the documentation : https://cfd.direct/openfoam/user-guide/v7-boundaries/

Quote:

empty: for solutions in in 2 (or 1) dimensions (2D/1D), the type used on each patch whose plane is normal to the 3rd (and 2nd) dimension for which no solution is required.

Regards,
Yann

October 25, 2020, 02:16	DamBreak tutorial in 3D	#1
Kahnbein.Kai Member Join Date: Feb 2018 Posts: 58 Rep Power: 8	Hello, i modified the DamBreak 2D tutorial, an add the third generation. The position of the alpha.phase 1 column i changed also. Here is a picture with three views at the timestep 0. https://www.imagebanana.com/s/1919/lHbZccfd.html And here at the timestep 399 (4 sec) https://www.imagebanana.com/s/1919/Qb68DaA8.html Why is the "water" collected at the edge of the x axis ? I dont changed the g file the value of the gravity is still 0 -9.81 0. Usually the water should distribute at the x axis and y axis face ? Best regards Kai

November 1, 2020, 13:16		#3
guin Member Rodrigo Join Date: Mar 2010 Posts: 98 Rep Power: 16	I didn't download your setup, but I'd suggest you to check whether your case is still using empty boundary conditions for the front and back patches. Kahnbein.Kai likes this.

November 3, 2020, 09:58		#8
Kahnbein.Kai Member Join Date: Feb 2018 Posts: 58 Rep Power: 8	Hey guin, thank you, for your detailed answer. I tried to reinstall openfoam 7 with the code Code: sudo apt-get -y install openfoam7 but it dosent install paraview 5.6.0 again ;( At the begin of the page for ubuntu you mentioned is the name of the paraview pack written down. So i tried Code: sudo apt-get -y isntall paraviewopenfoam56 And it works, perfektly Thank you very much for your help ! https://s1.imagebanana.com/file/201103/p3qpWEvC.png Best regards Kai ps: so i will look at the emtpy patches guin likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OF1912 overInterDyMFoam mass conservation in tutorial and actual case	Swift	OpenFOAM Running, Solving & CFD	6	August 6, 2020 04:04
[snappyHexMesh] The snappyMultiRegionHeater tutorial does not snap correctly	wildfire230	OpenFOAM Meshing & Mesh Conversion	2	May 10, 2019 06:19
fluxRequired OpenFoam Versions SimpleFoam Taylor Couette flow tutorial	mörli	OpenFOAM Running, Solving & CFD	0	April 9, 2019 11:50
STAR-CD Tutorial	shekhar aryal	STAR-CD	4	March 22, 2010 03:25
FoamX cannot run tutorial damBreak	ahorvat	OpenFOAM Bugs	5	July 8, 2008 18:24

November 1, 2020, 10:12		#2
Kahnbein.Kai Member Join Date: Feb 2018 Posts: 58 Rep Power: 8	Hello, nobody post a reply . So i think i have to load up the 0-, Constant- and the Systemfolder. Here is the link: https://we.tl/t-5LygYUke0n Is there anything wrong in my setup ? Best regards Kai

November 2, 2020, 11:52		#4
Kahnbein.Kai Member Join Date: Feb 2018 Posts: 58 Rep Power: 8	Hey guin, thank you for your reply. Yes, both of them are empty. In Paraview they are called defaultFaces. I will try to set a wall boundary aswell and run the case again. Best regards Kai by the way: i have an offtopic question. How you find the right vertices, faces and so on for the blockMeshDict File. I can open the geometry in Paraview, but i dont find a way to display the vertices or face numbers.

November 14, 2020, 02:11		#9
Kahnbein.Kai Member Join Date: Feb 2018 Posts: 58 Rep Power: 8	Hey guin, yes you are right, i changed the patches (front- and backwall) from "empty" to "wall". In the new run the water distributes "right" on the floor. But why does have the patches so much influence to the alpha1 phase ? What is different in these two simulations ? Best regards Kai