minIter for k and epsilon

johnb · May 5, 2009, 16:26

Hi,

I wonder if it is possible to specify minimum iterations “minIter” in the fvSolution for k and epsilon (well I tried and nothing happens, still results in No Iterations 0). Of course I can tighten the tolerance but shouldn’t there be away to force it to always run one iteration (i.e. minIter 1

. I am running v 1.5 and simpleFoam.

When I did look in the source code, I couldn’t find any files including minIter so maybe it isn’t implemented or used in v. 1.5?

Regards,
John

basneb · February 26, 2010, 06:36

Hello there,

I have the same problem as posted above. Is there any reason, why OpenFoam does not make at least 1 iteration, even if

minIter 1;

is stated?

Best regards

/Bastian

Attesz · April 17, 2012, 12:18

Hi,

I have the same problem with minIter in OF2.1. I think this is only for the extended version...

Did you find the solution?

Thanks,
Attila

aerogt3 · September 26, 2012, 16:42

Anyone have any luck with this? I too am finding that it doesn't complete any iterations even with this option turned on.

May 5, 2009, 16:26	minIter for k and epsilon	#1
johnb New Member John.B Join Date: Mar 2009 Posts: 14 Rep Power: 18	Hi, I wonder if it is possible to specify minimum iterations “minIter” in the fvSolution for k and epsilon (well I tried and nothing happens, still results in No Iterations 0). Of course I can tighten the tolerance but shouldn’t there be away to force it to always run one iteration (i.e. minIter 1. I am running v 1.5 and simpleFoam. When I did look in the source code, I couldn’t find any files including minIter so maybe it isn’t implemented or used in v. 1.5? Regards, John

April 17, 2012, 12:18		#3
Attesz Senior Member Attesz Join Date: Mar 2009 Location: Munich Posts: 368 Rep Power: 18	Hi, I have the same problem with minIter in OF2.1. I think this is only for the extended version... Did you find the solution? Thanks, Attila __________________ I am doing CFD Consulting Services. Ich biete CFD Strömungssimulationen an.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
SimpleFoam k and epsilon bounded	nedved	OpenFOAM Running, Solving & CFD	16	March 4, 2017 08:30
SimpleFoam k and epsilon bounded	nedved	OpenFOAM Running, Solving & CFD	1	November 25, 2008 20:21
Unknown error	sivakumar	OpenFOAM Pre-Processing	9	September 9, 2008 12:53
Epsilon Convergence Trouble	Carlos	FLUENT	4	August 27, 2007 11:22
How do k and epsilon vary with velocity?	nd	FLUENT	0	October 20, 2005 09:11

February 26, 2010, 06:36		#2
basneb New Member Bastian Nebenfuehr Join Date: Feb 2010 Location: Sverige Posts: 27 Rep Power: 17	Hello there, I have the same problem as posted above. Is there any reason, why OpenFoam does not make at least 1 iteration, even if minIter 1; is stated? Best regards /Bastian

September 26, 2012, 16:42		#4
aerogt3 Member Join Date: Mar 2009 Posts: 90 Rep Power: 18	Anyone have any luck with this? I too am finding that it doesn't complete any iterations even with this option turned on.