timeActivatedExplicitCellSource howto

ancsa · March 18, 2010, 09:48

Dear Foamers,

I was trying to set up a scalar point source to scalarTransportFoam and I found timeActivatedExplicitCellSource which seems to be the perfect tool, but I cannot figure out exactly how to use it. Does someone have experience, or is it used in some of the tutorials? Should I use a cellSetDict to define?

Any guidance is appreciated.

r08n · March 25, 2010, 06:59

Not sure about timeActivatedExplicitCellSource, but it seems to be similar to timeActivatedExplicitMulticomponentPointSource, which is used in tutorials/lagrangian/porousExplicitSourceReactingParcelFoam solver. There is a tutorial "filter"; you might look there and the source code for this solver. I just started raking through it myself. I suspect that the approach used in this solver and tutorial is described in the thesis http://powerlab.fsb.hr/ped/kturbo/op...olmPhD2008.pdf. Pls correct if I'm wrong, because these explicit sources are important to me too.

(The above apply to OF version 1.6 that I have; I don't know if these are included in other versions.)

ancsa · March 26, 2010, 06:48

Hi, I'm also having OF1.6 and I have also found this filter tutorial, but meanwhile I created a turbulent transport equation with a source term which seems to be working with a new source variable. I havent tested much yet though. The equation is very simple and it is not coupled but I dont need that so far, if this is enough for you I can send it.

March 18, 2010, 09:48	timeActivatedExplicitCellSource howto	#1
ancsa Member Aniko Rakai Join Date: Oct 2009 Location: Geneva Posts: 30 Rep Power: 18	Dear Foamers, I was trying to set up a scalar point source to scalarTransportFoam and I found timeActivatedExplicitCellSource which seems to be the perfect tool, but I cannot figure out exactly how to use it. Does someone have experience, or is it used in some of the tutorials? Should I use a cellSetDict to define? Any guidance is appreciated.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
HowTo Make paraFoam from OpenFOAM15 work on OpenSuse11 by installing Qt435 in home directory	wenterodt	OpenFOAM Installation	52	June 26, 2009 18:01
Howto install OpenFOAM on mandriva2009qt44 with Qt435 in home directory	gzy_1228	OpenFOAM Installation	0	November 15, 2008 15:31
A new Howto on the OpenFOAM Wiki Compiling OpenFOAM under Unix	mbeaudoin	OpenFOAM Installation	2	April 28, 2006 09:54
Howto manually merge a pst-file?	DrA	Siemens	2	December 6, 2005 09:57
chemical reaction - howto	Dan Sorensen	Siemens	1	February 21, 2000 10:20

March 25, 2010, 06:59		#2
r08n Member Robertas N. Join Date: Mar 2009 Location: Kaunas, Lithuania Posts: 53 Rep Power: 18	Not sure about timeActivatedExplicitCellSource, but it seems to be similar to timeActivatedExplicitMulticomponentPointSource, which is used in tutorials/lagrangian/porousExplicitSourceReactingParcelFoam solver. There is a tutorial "filter"; you might look there and the source code for this solver. I just started raking through it myself. I suspect that the approach used in this solver and tutorial is described in the thesis http://powerlab.fsb.hr/ped/kturbo/op...olmPhD2008.pdf. Pls correct if I'm wrong, because these explicit sources are important to me too. (The above apply to OF version 1.6 that I have; I don't know if these are included in other versions.)

March 26, 2010, 06:48		#3
ancsa Member Aniko Rakai Join Date: Oct 2009 Location: Geneva Posts: 30 Rep Power: 18	Hi, I'm also having OF1.6 and I have also found this filter tutorial, but meanwhile I created a turbulent transport equation with a source term which seems to be working with a new source variable. I havent tested much yet though. The equation is very simple and it is not coupled but I dont need that so far, if this is enough for you I can send it.