[Tutorials] Explanations of basic boundary conditions

fumiya · September 25, 2015, 10:31

I've uploaded an infographic explaining the meanings of the basic boundary conditions
implemented in OpenFOAM.
I hope it will be helpful for beginners.

http://www.slideshare.net/fumiyanoza...m-v24-53155320

fumiya · September 26, 2015, 10:29

I've uploaded another infographic explaining the time-dependent boundary conditions implemented in OpenFOAM.

http://www.slideshare.net/fumiyanoza...ns-in-openfoam

I hope it will be helpful.

coolcrasher · September 30, 2015, 06:15

Hi Fumiyan

your slides are very informative.

I am currently working on my master thesis on simulating centrifugal pump in openfoam.

I have followed your slides on them from slideshare and they were very informative.

Thanks a lot for your help and also I need a favour from you.

Do you have casefolders for pimpleDyMfoam, I have gone through the basic tutorials but I want to look at other case implementation of it.

Best Regards
Sravan

behnamEll · August 12, 2022, 05:41

hi

is there any way to deactivate a boundary condition and its contribution on LHS and RHS of matrix system?
somthing like empty boundary condition.

I want to set my own coefficients on the boundary cells of near specific patch and not affected by its boundary patch.

September 25, 2015, 10:31	Explanations of basic boundary conditions	#1
fumiya Senior Member Fumiya Nozaki Join Date: Jun 2010 Location: Yokohama, Japan Posts: 266 Blog Entries: 1 Rep Power: 18	I've uploaded an infographic explaining the meanings of the basic boundary conditions implemented in OpenFOAM. I hope it will be helpful for beginners. http://www.slideshare.net/fumiyanoza...m-v24-53155320 r08n, snak, cutter and 8 others like this. __________________ [Personal] Blog: https://caefn.com/ Twitter: https://twitter.com/FumiyaNozaki SlideShare: http://www.slideshare.net/fumiyanozaki96 Last edited by fumiya; September 25, 2015 at 18:32.

September 26, 2015, 10:29		#2
fumiya Senior Member Fumiya Nozaki Join Date: Jun 2010 Location: Yokohama, Japan Posts: 266 Blog Entries: 1 Rep Power: 18	I've uploaded another infographic explaining the time-dependent boundary conditions implemented in OpenFOAM. http://www.slideshare.net/fumiyanoza...ns-in-openfoam I hope it will be helpful. r08n and cutter like this. __________________ [Personal] Blog: https://caefn.com/ Twitter: https://twitter.com/FumiyaNozaki SlideShare: http://www.slideshare.net/fumiyanozaki96

August 12, 2022, 05:41	how to deactivate a boundary condition	#4
behnamEll New Member behnamCheraghi Join Date: Feb 2021 Posts: 14 Rep Power: 5	hi is there any way to deactivate a boundary condition and its contribution on LHS and RHS of matrix system? somthing like empty boundary condition. I want to set my own coefficients on the boundary cells of near specific patch and not affected by its boundary patch.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Centrifugal fan	j0hnny	CFX	13	October 1, 2019 13:55
CFD analaysis of Pelton turbine	amodpanthee	CFX	31	April 19, 2018 18:02
Multiphase flow - incorrect velocity on inlet	Mike_Tom	CFX	6	September 29, 2016 01:27
Error - Solar absorber - Solar Thermal Radiation	MichaelK	CFX	12	September 1, 2016 05:15
Error finding variable "THERMX"	sunilpatil	CFX	8	April 26, 2013 07:00

September 30, 2015, 06:15		#3
coolcrasher Member Sravan Kumar Join Date: May 2014 Posts: 57 Rep Power: 11	Hi Fumiyan your slides are very informative. I am currently working on my master thesis on simulating centrifugal pump in openfoam. I have followed your slides on them from slideshare and they were very informative. Thanks a lot for your help and also I need a favour from you. Do you have casefolders for pimpleDyMfoam, I have gone through the basic tutorials but I want to look at other case implementation of it. Best Regards Sravan