Which solver in OpenFOAM corresponds to the Eulerian Model in FLUENT?

paradism · March 20, 2017, 03:13

Hi, everyone.
I am trying to initiate my CFD simulation using OpenFOAM.
My system of interest is as follows:
Initially two fluids are homogenenously mixed by volume fraction of 1:1.
Two fluids have different values of density. So under gravity, stratification of two fluids takes place.
Finally the two fluids will be almost completely separated by gravity.
Diffusion and surface tension are assumed to be negligible. Cyclic boundary condition will be applied along horizontal directions.
VOF or mixture model do not seem to be applicable, cause they do not calculate the relative motion of two fluids.
According to the documentation research, I found that Eulerian model in FLUENT seem to meet my needs.
However, I only have the OpenFOAM.
Is there any multiphase model in OpenFOAM that solves the momentum equation separately for n phases?

P.S. : Unlike Fluent, OpenFOAM documentation (TutorialGuide.pdf, UserGuide.pdf) does not tell much about the theories behind the solvers.
If there exists a overall theory documentation of OpenFOAM, can anybody tell me?

juho · March 20, 2017, 09:35

reactingTwoPhaseEulerFoam: https://github.com/OpenFOAM/OpenFOAM...PhaseEulerFoam

or

reactingMultiphaseEulerFoam: https://github.com/OpenFOAM/OpenFOAM...erFoam/laminar

There are also legacy twoPhaseEulerFoam and multiPhaseEulerFoam solvers, but the newer "reacting" versions are more general and can be used also for non-reacting and isothermal simulations.

March 20, 2017, 03:13	Which solver in OpenFOAM corresponds to the Eulerian Model in FLUENT?	#1
paradism New Member Jihoe Kwon Join Date: Mar 2017 Posts: 1 Rep Power: 0	Hi, everyone. I am trying to initiate my CFD simulation using OpenFOAM. My system of interest is as follows: Initially two fluids are homogenenously mixed by volume fraction of 1:1. Two fluids have different values of density. So under gravity, stratification of two fluids takes place. Finally the two fluids will be almost completely separated by gravity. Diffusion and surface tension are assumed to be negligible. Cyclic boundary condition will be applied along horizontal directions. VOF or mixture model do not seem to be applicable, cause they do not calculate the relative motion of two fluids. According to the documentation research, I found that Eulerian model in FLUENT seem to meet my needs. However, I only have the OpenFOAM. Is there any multiphase model in OpenFOAM that solves the momentum equation separately for n phases? P.S. : Unlike Fluent, OpenFOAM documentation (TutorialGuide.pdf, UserGuide.pdf) does not tell much about the theories behind the solvers. If there exists a overall theory documentation of OpenFOAM, can anybody tell me?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PEMFC model with FLUENT	brahimchoice	FLUENT	22	April 19, 2020 15:44
OpenFOAM v3.0+ ??	SBusch	OpenFOAM	22	December 26, 2016 14:24
Lift and Drag pattern change wit FLUENT 16 and 13 PISO for same mesh n solver setting	arunraj	FLUENT	0	June 2, 2016 22:58
Fluent :- turbulence Model	prince_pahariaa	FLUENT	9	May 20, 2016 03:41
Fluent OpenFoam comparison kepsilon model	alimansouri	OpenFOAM Running, Solving & CFD	5	January 19, 2009 09:35

March 20, 2017, 09:35		#2
juho Member Juho Peltola Join Date: Mar 2009 Location: Finland Posts: 89 Rep Power: 17	reactingTwoPhaseEulerFoam: https://github.com/OpenFOAM/OpenFOAM...PhaseEulerFoam or reactingMultiphaseEulerFoam: https://github.com/OpenFOAM/OpenFOAM...erFoam/laminar There are also legacy twoPhaseEulerFoam and multiPhaseEulerFoam solvers, but the newer "reacting" versions are more general and can be used also for non-reacting and isothermal simulations.