CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > OpenFOAM

How to run bubbleInterTrackFoam in parallel?

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   October 9, 2017, 09:21
Question How to run bubbleInterTrackFoam in parallel?
  #1
New Member
 
Join Date: May 2017
Posts: 2
Rep Power: 0
jato is on a distinguished road
Hello everybody,
I tried to run the solver bubbleInterTrackFoam to simulate the rising of a bubble. However, when I tried to run it in parallel I get the following error:

[1]
[1]
[1] --> FOAM FATAL IO ERROR:
[1] cannot open file
[1]
[1] file: /media/jato/Jato/simulation/bubbleintertrackfoam/bubble3D-bidirectional-parallel/processor1/0/fluidIndicator at line 0.
[1]
[1] From function regIOobject::readStream()
[1] in file db/regIOobject/regIOobjectRead.C at line 61.
[1]
FOAM parallel run exiting
[0]
[0]
[0] --> FOAM FATAL IO ERROR:
[0] cannot open file
[0]
[0] file: /media/jato/Jato/simulation/bubbleintertrackfoam/bubble3D-bidirectional-parallel/processor0/0/fluidIndicator at line 0.
[0]
[0] From function regIOobject::readStream()
[0] in file db/regIOobject/regIOobjectRead.C at line 61.
[0]
FOAM parallel run exiting
[0]
[1]
--------------------------------------------------------------------------
MPI_ABORT was invoked on rank 0 in communicator MPI_COMM_WORLD
with errorcode 1.

NOTE: invoking MPI_ABORT causes Open MPI to kill all MPI processes.
You may or may not see output from other processes, depending on
exactly when Open MPI kills them.
--------------------------------------------------------------------------
--------------------------------------------------------------------------
mpirun has exited due to process rank 0 with PID 28311 on
node jato-Precision-Tower-7810 exiting improperly. There are two reasons this could occur:

1. this process did not call "init" before exiting, but others in
the job did. This can cause a job to hang indefinitely while it waits
for all processes to call "init". By rule, if one process calls "init",
then ALL processes must call "init" prior to termination.

2. this process called "init", but exited without calling "finalize".
By rule, all processes that call "init" MUST call "finalize" prior to
exiting or it will be considered an "abnormal termination"

This may have caused other processes in the application to be
terminated by signals sent by mpirun (as reported here).

Could you please give me a hint?
jato is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
MPI error in parallel application usv001 OpenFOAM Programming & Development 2 September 14, 2017 11:30
Foam::error::PrintStack almir OpenFOAM Running, Solving & CFD 83 July 22, 2017 08:26
snappyHexMesh error "Cannot determine normal vector from patches." lethu OpenFOAM Meshing & Mesh Conversion 0 July 10, 2017 04:15
problem during mpi in server: expected Scalar, found on line 0 the word 'nan' muth OpenFOAM Running, Solving & CFD 2 April 10, 2015 05:42
Parallel Run on dynamically mounted partition braennstroem OpenFOAM Running, Solving & CFD 14 October 5, 2010 14:43


All times are GMT -4. The time now is 04:06.