wallShearStress & creatTurbulenceFields in OF 1.6

ar_mofidi · April 12, 2010, 07:05

Hi,
I have a turbulent channel flow with slip BC. on bottom wall and I have solved this channel with channelFoam. I would like to calculate the WallShearStress and also I want to create turbulence fields for calculating the Reynolds stress R, in OpenFoam 1.6. I should be remind that my Turbulence Model is LES. How can I do that?

Regards,
Alireza

idrama · April 12, 2010, 11:14

Have ya already try the post-processing tool wallShearStress ?

ar_mofidi · April 13, 2010, 03:31

Hi idrama

yes, I have used wallShearStress but it didn't work. when I use this term this message appears:

Create time

Create mesh for time = 3.00141

Time = 3.00141
Reading field U

Reading/calculating face flux field phi

Selecting incompressible transport model Newtonian

cannot open file

file: /home/sekhavat/OpenFOAM/sekhavat-1.6/run/tutorials/incompressible/channelFoamslip/channeltopwallslip/constant/RASProperties at line 0.

From function regIOobject::readStream()
in file db/regIOobject/regIOobjectRead.C at line 62.

FOAM exiting

idrama · April 15, 2010, 03:39

Hallo,

wallShearStress is dependent on on turbulence models, hence is need RASProperties. You must check that. Strangely, the time mesh value 3.**.
If you cannot fix it, check the Forum for "computing wall shear stresses", I think. In this Forum, there are already hot discussens about that.

cheers

April 12, 2010, 07:05	wallShearStress & creatTurbulenceFields in OF 1.6	#1
ar_mofidi New Member alireza Join Date: Apr 2009 Location: iran Posts: 11 Rep Power: 17	Hi, I have a turbulent channel flow with slip BC. on bottom wall and I have solved this channel with channelFoam. I would like to calculate the WallShearStress and also I want to create turbulence fields for calculating the Reynolds stress R, in OpenFoam 1.6. I should be remind that my Turbulence Model is LES. How can I do that? Regards, Alireza

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
k-omega-SST model (OF 1.6) - turbulent flat plate	cboss	OpenFOAM Running, Solving & CFD	25	August 9, 2016 09:53
install OpenFoam 1.6 by building source: how?	niudie	OpenFOAM Installation	13	April 26, 2011 00:48
problems in Two Phase flow using twoPhaseEulerFoam with OpenFoam 1.6	raagh77	OpenFOAM Running, Solving & CFD	0	March 6, 2010 05:11
kOmegaSST in openfoam 1.6	Gearb0x	OpenFOAM	2	March 3, 2010 06:02
utility utilization in 1.6 !	smm1457	OpenFOAM Running, Solving & CFD	3	January 17, 2010 15:06

April 12, 2010, 11:14		#2
idrama Senior Member Claus Meister Join Date: Aug 2009 Location: Wiesbaden, Germany Posts: 241 Rep Power: 17	Have ya already try the post-processing tool wallShearStress ?

April 13, 2010, 03:31		#3
ar_mofidi New Member alireza Join Date: Apr 2009 Location: iran Posts: 11 Rep Power: 17	Hi idrama yes, I have used wallShearStress but it didn't work. when I use this term this message appears: Create time Create mesh for time = 3.00141 Time = 3.00141 Reading field U Reading/calculating face flux field phi Selecting incompressible transport model Newtonian cannot open file file: /home/sekhavat/OpenFOAM/sekhavat-1.6/run/tutorials/incompressible/channelFoamslip/channeltopwallslip/constant/RASProperties at line 0. From function regIOobject::readStream() in file db/regIOobject/regIOobjectRead.C at line 62. FOAM exiting

April 15, 2010, 03:39		#4
idrama Senior Member Claus Meister Join Date: Aug 2009 Location: Wiesbaden, Germany Posts: 241 Rep Power: 17	Hallo, wallShearStress is dependent on on turbulence models, hence is need RASProperties. You must check that. Strangely, the time mesh value 3.**. If you cannot fix it, check the Forum for "computing wall shear stresses", I think. In this Forum, there are already hot discussens about that. cheers