openfoam-1.7-extend. when?

argonaut · April 5, 2011, 03:24

Is there a plan to release 1.7-ext version in near future?

hjasak · April 6, 2011, 09:24

Yes

There is a few things to wrap up, contributions have been collected and the main obstacle is doing the final phase without driving me to lunacy... Is there anything in particular you are missing?

I will keep you posted,

Hrv

argonaut · April 7, 2011, 09:35

Actually, no.

Probably, what I will need, is in 1.6-ext already. I would say: because I start to get into the code right now, I prefer to use the latest version.

My current investigation is not so difficult in general: heat transfer with heat source in connected solids. The problem - I use transient coefficients everywhere. I made Robin BC on the surface with groovyBC; physical coefficients I defined as fields and approximated as polynomials.

Current questions for me right now is:

a) how better to treat connected solids,
i.e., how correctly implement temperature-dependent conjugation (transmission) conditions. Before, I used setFields to set different values of physical properties, I used "harmonic" approximation of conductivity in laplacian but the results was worse than for "linear". As far as I know as mathematician, linear approximation, theoretically, leads to other solution than original. Not so big trouble with simple mathematical problems, but I still care for my future projects

b) how to implement BC with the second order of approximation

c) in distant future: how to implement flow of direct electrical current in metal with Joule heating. Quick search did not gave me awareness if this is already implemented or available.

April 5, 2011, 03:24	openfoam-1.7-extend. when?	#1
argonaut New Member Raimonds Vilums Join Date: Oct 2010 Posts: 17 Rep Power: 16	Is there a plan to release 1.7-ext version in near future?

April 6, 2011, 09:24		#2
hjasak Senior Member Hrvoje Jasak Join Date: Mar 2009 Location: London, England Posts: 1,905 Rep Power: 33	Yes There is a few things to wrap up, contributions have been collected and the main obstacle is doing the final phase without driving me to lunacy... Is there anything in particular you are missing? I will keep you posted, Hrv __________________ Hrvoje Jasak Providing commercial FOAM/OpenFOAM and CFD Consulting: http://wikki.co.uk

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
LowRe-SST in OpenFOAM 1.7?	Peter85	OpenFOAM Running, Solving & CFD	17	February 24, 2015 20:03
OpenFOAM 1.7 installation on Redhat linux	maxims	OpenFOAM Installation	2	November 30, 2012 04:29
[swak4Foam] OpenFOAM 1.6 and 1.7 with interFoam, groovyBC give different strange results	Arnoldinho	OpenFOAM Community Contributions	7	December 9, 2010 16:29
Cross-compiling OpenFOAM 1.7.0 on Linux for Windows 32 and 64bits with Mingw-w64	wyldckat	OpenFOAM Announcements from Other Sources	3	September 8, 2010 06:25
OpenFOAM 1.7 - openSUSE 11.3 - gcc 4.5.0	alberto	OpenFOAM	12	July 28, 2010 11:59

April 7, 2011, 09:35		#3
argonaut New Member Raimonds Vilums Join Date: Oct 2010 Posts: 17 Rep Power: 16	Actually, no. Probably, what I will need, is in 1.6-ext already. I would say: because I start to get into the code right now, I prefer to use the latest version. My current investigation is not so difficult in general: heat transfer with heat source in connected solids. The problem - I use transient coefficients everywhere. I made Robin BC on the surface with groovyBC; physical coefficients I defined as fields and approximated as polynomials. Current questions for me right now is: a) how better to treat connected solids, i.e., how correctly implement temperature-dependent conjugation (transmission) conditions. Before, I used setFields to set different values of physical properties, I used "harmonic" approximation of conductivity in laplacian but the results was worse than for "linear". As far as I know as mathematician, linear approximation, theoretically, leads to other solution than original. Not so big trouble with simple mathematical problems, but I still care for my future projects b) how to implement BC with the second order of approximation c) in distant future: how to implement flow of direct electrical current in metal with Joule heating. Quick search did not gave me awareness if this is already implemented or available.