CFD Online Discussion Forums
Page 2 of 2 1 2
Show 40 post(s) from this thread on one page

CFD Online Discussion Forums (https://www.cfd-online.com/Forums/)
-   OpenFOAM Meshing & Mesh Conversion (https://www.cfd-online.com/Forums/openfoam-meshing/)
-   -   [Other] Failed 1 mesh check (https://www.cfd-online.com/Forums/openfoam-meshing/92425-failed-1-mesh-check.html)

A.Wendy May 23, 2013 06:20
hi,

are all of this patches defined in the 0-folder?
Quote:
topAndBottom 440 884 ok (non-closed singly connected)
inlet 120 242 ok (non-closed singly connected)
outlet 120 242 ok (non-closed singly connected)
front 51101 52012 ok (non-closed singly connected)
back 51101 52012 ok (non-closed singly connected)
airfoil_airfoil 5168 5491 ok (non-closed singly connected)
best wishes

Andreas

faraz22 May 24, 2013 08:37
Quote:
Originally Posted by s.m (Post 429451)
Hi,faraz
i didn't get what do you mean:( sorry.
i put my blockMeshDict and the checkMesh files in the following, would you please tell me again.
thank you very much.
Hello S.m please try to upload some pictures of your background mesh here .. ill see. actually the faces your have mentioned in blockmesh are those which you need for your case. but in order to avoid the given error , you always have to define all the remaining faces of sketch or drawing in blockmesh ... no matter your need those faces or not. may you get it?

s.m May 25, 2013 02:59
4 Attachment(s)
Quote:
Originally Posted by faraz22 (Post 429785)
Hello S.m please try to upload some pictures of your background mesh here .. ill see. actually the faces your have mentioned in blockmesh are those which you need for your case. but in order to avoid the given error , you always have to define all the remaining faces of sketch or drawing in blockmesh ... no matter your need those faces or not. may you get it?
Hi faraz,
i put a screenshot of my mesh with it's patch name. my background mesh is a domain with inlet outlet top and bottom after running the snappyHexMesh i 'll have this mesh that i upload here.
i put my block mesh also, i want to know what should i add to my blockMeshDict ?
airfoil_airfoil?

s.m May 26, 2013 12:30
Quote:
Originally Posted by faraz22 (Post 429785)
Hello S.m please try to upload some pictures of your background mesh here .. ill see. actually the faces your have mentioned in blockmesh are those which you need for your case. but in order to avoid the given error , you always have to define all the remaining faces of sketch or drawing in blockmesh ... no matter your need those faces or not. may you get it?
Hi faraz,
i understand what should i do, thank you very much for your explanation.:)
Best Regards.

wes1204 September 18, 2013 03:42
http://www.tfd.chalmers.se/~hani/kur...eTutorials.pdf

you can get the solution from 77page on this document.

just refer it.

sk11 April 14, 2017 07:42
Thanks wyldkat! extruding solved my problem!

ltiago94 April 4, 2018 18:53
Quote:
Originally Posted by jhoepken (Post 324056)
A 2D mesh in OpenFOAM is a 3D mesh with only one cell in planar direction and the planar patches have to be of type empty. For a proper 2D mesh, the start and end points of the edges normal to the planar patches have to be at the same "not empty" coordinates. This is not the case with your mesh and that is why your 2D simulation does not converge and checkMesh complains about those edges.
Hello Jens, can you tell me how I solve this because I'm having this problem right now.

Thanks

Luis


All times are GMT -4. The time now is 18:27.
Page 2 of 2 1 2
Show 40 post(s) from this thread on one page