wall heat flux

niharika · February 24, 2016, 06:16

can wall heat flux values be obtained from phoenics software. If yes then how?

TJH-CHAM · February 25, 2016, 07:24

Hi niharika,

If the heat flux is at a PLATE boundary with a surface temperature, then the heat flux will be printed in the RESULT file in the 'Sources and sinks' section as the Nett source of TEM1 for that object. For a BLOCKAGE object, the nett TEM1 source will be for the entire object, not individual faces. You can also STORE(QDX,QDY,QDZ) (either directly in Q1 or from Menu, Models, Solution control / Extra variables, STORE). At the end of the run, these will be filled with the X-, Y- and Z-directed heat fluxes. With a little InForm you can add these up over any area.

That is the best answer I can give you unfortunately without knowing more about your case. If that doesn't help, could you perhaps be more specific and we will try our best to help.

Thanks

niharika · February 27, 2016, 03:45

Thank you so much for the reply. I have a blockage which is a heat source in between the domain fluid. so it has two boundaries with the domain fluid. I want to know the wall heat flux for the two boundaries. Can it be done? I will try to store the variables you suggested and thank you very much.

TJH-CHAM · March 3, 2016, 07:16

Hi again,

Storing those variables should give you the information you need. If that doesn't work please let me know and I will try to help.

Thanks,

February 24, 2016, 06:16	wall heat flux	#1
niharika New Member niharika Join Date: Feb 2016 Posts: 3 Rep Power: 9	can wall heat flux values be obtained from phoenics software. If yes then how?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Radiation interface	hinca	CFX	15	January 26, 2014 18:11
An error has occurred in cfx5solve:	volo87	CFX	5	June 14, 2013 18:44
how to export "wall heat flux" to tecplot?	victor	CFX	3	November 27, 2008 10:45
CFX - wall heat flux	divarano	CFX	2	December 4, 2006 17:14
Basic question: UDF for wall heat flux	Carl	FLUENT	1	August 5, 2006 20:01

February 25, 2016, 07:24		#2
TJH-CHAM New Member Tom Horsfield Join Date: Dec 2015 Posts: 5 Rep Power: 9	Hi niharika, If the heat flux is at a PLATE boundary with a surface temperature, then the heat flux will be printed in the RESULT file in the 'Sources and sinks' section as the Nett source of TEM1 for that object. For a BLOCKAGE object, the nett TEM1 source will be for the entire object, not individual faces. You can also STORE(QDX,QDY,QDZ) (either directly in Q1 or from Menu, Models, Solution control / Extra variables, STORE). At the end of the run, these will be filled with the X-, Y- and Z-directed heat fluxes. With a little InForm you can add these up over any area. That is the best answer I can give you unfortunately without knowing more about your case. If that doesn't help, could you perhaps be more specific and we will try our best to help. Thanks

February 27, 2016, 03:45		#3
niharika New Member niharika Join Date: Feb 2016 Posts: 3 Rep Power: 9	Thank you so much for the reply. I have a blockage which is a heat source in between the domain fluid. so it has two boundaries with the domain fluid. I want to know the wall heat flux for the two boundaries. Can it be done? I will try to store the variables you suggested and thank you very much.

March 3, 2016, 07:16		#4
TJH-CHAM New Member Tom Horsfield Join Date: Dec 2015 Posts: 5 Rep Power: 9	Hi again, Storing those variables should give you the information you need. If that doesn't work please let me know and I will try to help. Thanks,