|
[Sponsors] |
May 5, 2002, 04:10 |
PHI->Tecplt.dat
|
#1 |
Guest
Posts: n/a
|
When I want to transfer my *.PHI file to *.dat using PHOTEC.exe, it could not run with the large size PHI file, my PHI is 40MB, I don't think it's a large file,but no problem with other small phi files, I don't know why, anyone can tell me the reasons? Thanks.
|
|
May 10, 2002, 10:55 |
Re: PHI->Tecplt.dat
|
#2 |
Guest
Posts: n/a
|
The default maximum number of nodes ((nx+1)*(ny+1)*(nz+1))=150000, which is too small for a bit more complicated geometry. I've met the same problem. I tried to recompile 'Tec.for' but it seems there is a relation between 'tec.for' and 'main.for'. My 'main.for' was compiled for the RAM size of 256M, so the 'tec.for' cannot allocate memory more than 256M, otherwise it will give an error message.
You will have to compile 'tec.for' and then link it with 'bldtec.bat'. You will get a new copy of tecexe.exe after you have done this. Probably the people in CHAM are too busy to drop by. So I'm not sure if what I've mentioned above is correct. Hope this may help. Regards. |
|
May 10, 2002, 14:13 |
Re: PHI->Tecplt.dat
|
#3 |
Guest
Posts: n/a
|
Oops, I was wrong. There is no connection between 'Tec.for' and 'Main.for'. However, an error message still exists when the maximum node number exceeds 3600000.
|
|
May 12, 2002, 01:34 |
Re: PHI->Tecplt.dat
|
#4 |
Guest
Posts: n/a
|
Dear Hu, Thanks for your knid help, I'll try.
|
|
May 12, 2002, 02:20 |
Re: PHI->Tecplt.dat
|
#5 |
Guest
Posts: n/a
|
Could you tell me how to link the "tec.for" with "bldtec.dat", following your suggestion, maybe I have met the same trouble with you,"unresolved external symbol _TECMAIN@240' How did you do about this? Thanks
|
|
May 12, 2002, 08:50 |
Re: PHI->Tecplt.dat
|
#6 |
Guest
Posts: n/a
|
You have to compile 'tec.for' before you can link it with 'bldtec.bat'. Therefore you need a Digital Fortran compiler. Using the compiler to generate 'tec.obj' only and then you can link the new 'tec.obj' with 'bldtec.bat' for a new copy of 'tecexe.exe'. Remember to backup your original copy of these files when you are doing this.
Good luck! |
|
May 27, 2002, 03:10 |
Re: PHI->Tecplt.dat
|
#7 |
Guest
Posts: n/a
|
Thank you for your kind help.
|
|
June 29, 2002, 09:06 |
Re: PHI->Tecplt.dat
|
#8 |
Guest
Posts: n/a
|
Sear,
You can ask Mr: * nitin <nitinkd@yahoo.com> or * Baizh.sun <cdybz@263.net> I sent them a fortran program which done by my self. It transfer the PHI file to tec.dat file . Also you must open and correct your .dat files with EDIT on msdos command. |
|
July 19, 2002, 03:14 |
Re: PHI->Tecplt.dat
|
#9 |
Guest
Posts: n/a
|
Thanks.
|
|
|
|