CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > Phoenics

gas solid pipe flow

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   October 23, 2003, 12:58
Default gas solid pipe flow
  #1
tahar
Guest
 
Posts: n/a
Hi, i am a beginner with Phoenix.I want to know how to simulate a gas-solid pipe flow with Phoenix 3.4 in cartesian coordinates . When I use the Ipsa two phase flow ( air- sand), the domain material is phase 1 (air), phase 2 ( sand), the problem is how to deal with the pipe material. I have not seen a demo on the same thing. thank you
  Reply With Quote

Old   October 25, 2003, 11:49
Default Re: gas solid pipe flow
  #2
moh
Guest
 
Posts: n/a
you should not model the pipe as blockage but perhaps as thinpipe or plate. hope this help you moh
  Reply With Quote

Old   October 27, 2003, 16:06
Default Re: gas solid pipe flow
  #3
tahar
Guest
 
Posts: n/a
hi,

thank you for your advice, how can I discard the computational domain outside the pipe. for the two phase flow inside the pipe, I have an inlet, the pipe is simulated as ( thinpipe, blockage), and an outlet. the method is ipsa full. thank you
  Reply With Quote

Old   October 29, 2003, 18:17
Default Re: gas solid pipe flow
  #4
Leon Mills
Guest
 
Posts: n/a
tahar,

If you are looking at pipe flow try using polar co-ordinates.

Otherwise, make the intlet and outlet the same size as the pipe, keep the area around the pipe as aminimum. This should speed up computational time and keep the flow inside the pipe.

Hope this helps - Leon
  Reply With Quote

Old   October 30, 2003, 11:27
Default Re: gas solid pipe flow
  #5
tahar
Guest
 
Posts: n/a
Leon,

Thank you for your advice. Because the geometry of the system we are studying consist of two horizontal pipe, and one vertical. It'a difficult to use polar coordinate.

I began to simulate the flow in one horizontal pipe. The model consist of one inlet, one outlet, and a pipe ( thinpipe, blockage). The inlet and outlet size are the same as the pipe. Even if the area around the pipe is minimum, the computational is performed inside and outside the pipe. So my question is can I limit my computational domain to the flow inside the pipe itself.
  Reply With Quote

Old   October 30, 2003, 18:21
Default Re: gas solid pipe flow
  #6
Leon Mills
Guest
 
Posts: n/a
tahar,

Unfortunately, not that I am aware of. Some one may correctly me on this one if I am wrong.

Try looking a fine gri volumes. This way you can refine your mesh inside the pipes and have a very course mesh outside of the pipe.

Another option maybe to look at BFC. I dont use this system often but it maybe of some use to your problem.

Hope this helps.

Leon
  Reply With Quote

Old   November 3, 2003, 13:03
Default Re: gas solid pipe flow
  #7
tahar
Guest
 
Posts: n/a
Leon

Once again I than you for your suggestion. I think that with the thinpipe object geometry there is a problem since the wall thickness is much more smaller than the grid cell size and any grid refinement is difficult. so I will try BFC. regards,

Tahar
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Is there any 1D solid/gas flow code in pipe? dongye Main CFD Forum 0 November 21, 2007 22:05
1D model for gas/solid flow in vertical/honr pipe? dongye Main CFD Forum 0 October 1, 2007 23:23
2d example of solid-water flow in a pipe? www_sun Phoenics 1 March 20, 2002 09:34
gas solid flow in a pipe Pandu CFX 0 July 30, 2001 17:53
modelling for gas-solid flow in horizontal pipe daninwin CFX 9 February 8, 2001 00:47


All times are GMT -4. The time now is 04:20.