k-w turbulence model

May 17, 2006, 09:36

Hi every one.

I want to use other than standard k-e model in PHOENICs but I have big problems. For example whenever I active k-w turbulence model from "menu/models" I see the following error in result file:

"RDDF10: Error reading COVAL data (2) RDDF10: Error reading data (2) Error in reading STORSA or STORWD !"

or when I choose two-layer k-e model I don't see any error in result file but the run interrupts without any solution and the earth window closes. The final lines of result file are :

"Group 24. Dumps For Restarts SAVE = T ;AUTOPS = F ;NOWIPE = F NSAVE =CHAM --- INTEGRATION OF EQUATIONS BEGINS ---"

What's wrong? Should I apply a specific condition in Inlet boundaries when I switch to models other than k-e?

I'd be grateful if you help me. Regards

November 11, 2006, 03:44

Hi every one.

I want to use other than standard k-e model in PHOENICs but I have big problems. For example whenever I active k-w turbulence model from "menu/models" I see the following error in result file:

"RDDF10: Error reading COVAL data (2) RDDF10: Error reading data (2) Error in reading STORSA or STORWD !"

or when I choose two-layer k-e model I don't see any error in result file but the run interrupts without any solution and the earth window closes. The final lines of result file are :

"Group 24. Dumps For Restarts SAVE = T ;AUTOPS = F ;NOWIPE = F NSAVE =CHAM --- INTEGRATION OF EQUATIONS BEGINS ---"

What's wrong? Should I apply a specific condition in Inlet boundaries when I switch to models other than k-e?

I'd be grateful if you help me. Regards

May 17, 2006, 09:36	k-w turbulence model	#1
Sima Baheri Guest Posts: n/a	Hi every one. I want to use other than standard k-e model in PHOENICs but I have big problems. For example whenever I active k-w turbulence model from "menu/models" I see the following error in result file: "RDDF10: Error reading COVAL data (2) RDDF10: Error reading data (2) Error in reading STORSA or STORWD !" or when I choose two-layer k-e model I don't see any error in result file but the run interrupts without any solution and the earth window closes. The final lines of result file are : "Group 24. Dumps For Restarts SAVE = T ;AUTOPS = F ;NOWIPE = F NSAVE =CHAM --- INTEGRATION OF EQUATIONS BEGINS ---" What's wrong? Should I apply a specific condition in Inlet boundaries when I switch to models other than k-e? I'd be grateful if you help me. Regards

November 11, 2006, 03:44	Re: k-w turbulence model	#2
Sima Baheri Guest Posts: n/a	Hi every one. I want to use other than standard k-e model in PHOENICs but I have big problems. For example whenever I active k-w turbulence model from "menu/models" I see the following error in result file: "RDDF10: Error reading COVAL data (2) RDDF10: Error reading data (2) Error in reading STORSA or STORWD !" or when I choose two-layer k-e model I don't see any error in result file but the run interrupts without any solution and the earth window closes. The final lines of result file are : "Group 24. Dumps For Restarts SAVE = T ;AUTOPS = F ;NOWIPE = F NSAVE =CHAM --- INTEGRATION OF EQUATIONS BEGINS ---" What's wrong? Should I apply a specific condition in Inlet boundaries when I switch to models other than k-e? I'd be grateful if you help me. Regards

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
changing model constants in k-e turbulence model	Sunil	CFX	3	October 3, 2006 12:12
turbulence model	greg	FLUENT	3	August 26, 2006 11:07
v2-f model of turbulence	abdellah	FLUENT	2	February 27, 2005 00:49
HELP! TURBULENCE k-e OR k-omega TURBULENCE MODEL?	Mirek Kabacinski	FLUENT	5	August 24, 2003 22:31
k-w turbulence model	allan	Main CFD Forum	4	February 20, 2002 13:05