Boundry conditions for O-grid mesh

saad · September 16, 2014, 15:22

Dear All,

Using pointwise, I have created hyperbolic O-grid topology 2d mesh for airfoil, now for boundry condition, what I am doing, is to split the outer circle into two semi curves (for velocity inlet and pressure outlet)

Is this right approach?? or there is other way around? kindly help
my solver is ansys fluent

Thanks

cnsidero · September 17, 2014, 09:57

That depends on the type of gas model you are using. If you are assuming a compressible flow (ideal gas), Fluent has a characteristic boundary condition call "farfield" where you set the freestream conditions. This boundary condition type would allow you to use the whole circle.

However, this boundary condition can not be used for incompressible flow (constant density). Therefore, the approach you are using would be appropriate.

BSengupta · December 30, 2018, 17:13

Hi!
What shall be BC in case of openfoam?

tcarrigan · January 3, 2019, 12:16

Quote:

Originally Posted by BSengupta

Hi!
What shall be BC in case of openfoam?

There's a "freestream" and "freestreamPressure" type you can use with OpenFOAM. You'll just need to specify a "freestreamValue" and you're good to go.

BSengupta · January 4, 2019, 03:00

Thank you very much. It was successful.

Kfj · February 9, 2020, 01:37

I used farfield as velocity inlet, airfoil as wall.. which boundary condition I give for sides?...This was the problem that I faced in ansys fluent solver.. can anyone help me?

Kfj · February 9, 2020, 01:39

I used farfield as velocity inlet, airfoil as wall for o grid mesh.. which boundary condition I give for sides?...This was the problem that I faced in ansys fluent solver.. can anyone help me?.. in ansys fluent I got big confusion what I give for sides?

Kfj · February 22, 2020, 01:12

hi!
what shall be BC incase of ansys fluent

September 16, 2014, 15:22	Boundry conditions for O-grid mesh	#1
saad New Member saad Join Date: Apr 2014 Posts: 1 Rep Power: 0	Dear All, Using pointwise, I have created hyperbolic O-grid topology 2d mesh for airfoil, now for boundry condition, what I am doing, is to split the outer circle into two semi curves (for velocity inlet and pressure outlet) Is this right approach?? or there is other way around? kindly help my solver is ansys fluent Thanks

February 9, 2020, 01:37	O grid mesh boundary condition in ansys fluent solver	#6
Kfj New Member Jay Join Date: Feb 2020 Posts: 3 Rep Power: 4	I used farfield as velocity inlet, airfoil as wall.. which boundary condition I give for sides?...This was the problem that I faced in ansys fluent solver.. can anyone help me?

February 9, 2020, 01:39	O grid mesh boundary condition in ansys fluent solver	#7
Kfj New Member Jay Join Date: Feb 2020 Posts: 3 Rep Power: 4	I used farfield as velocity inlet, airfoil as wall for o grid mesh.. which boundary condition I give for sides?...This was the problem that I faced in ansys fluent solver.. can anyone help me?.. in ansys fluent I got big confusion what I give for sides?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
sliding mesh problem in CFX	Saima	CFX	46	September 11, 2021 07:38
[snappyHexMesh] problems generating clean mesh	Christian_tt	OpenFOAM Meshing & Mesh Conversion	2	June 20, 2019 05:39
3D Hybrid Mesh Errors	DarrenC	ANSYS Meshing & Geometry	11	August 5, 2013 06:42
Combustion Convergence problems	Art Stretton	Phoenics	5	April 2, 2002 05:59
Grid Independent Solution	Chuck Leakeas	Main CFD Forum	2	May 26, 2000 11:18

September 17, 2014, 09:57		#2
cnsidero Senior Member Chris Sideroff Join Date: Mar 2009 Location: Ottawa, ON, CAN Posts: 422 Rep Power: 20	That depends on the type of gas model you are using. If you are assuming a compressible flow (ideal gas), Fluent has a characteristic boundary condition call "farfield" where you set the freestream conditions. This boundary condition type would allow you to use the whole circle. However, this boundary condition can not be used for incompressible flow (constant density). Therefore, the approach you are using would be appropriate.

December 30, 2018, 17:13		#3
BSengupta Member Bidesh Sengupta Join Date: Sep 2018 Posts: 71 Rep Power: 5	Hi! What shall be BC in case of openfoam?

January 4, 2019, 03:00		#5
BSengupta Member Bidesh Sengupta Join Date: Sep 2018 Posts: 71 Rep Power: 5	Thank you very much. It was successful.

February 22, 2020, 01:12		#8
Kfj New Member Jay Join Date: Feb 2020 Posts: 3 Rep Power: 4	hi! what shall be BC incase of ansys fluent