Forum: ANSYS Meshing & Geometry
May 18, 2017, 17:10
|
Replies: 5
Views: 5,015
|
Forum: ANSYS Meshing & Geometry
April 20, 2017, 09:15
|
Replies: 3
Views: 1,529
Before trying to fill, you need to run some...
Before trying to fill, you need to run some checks. Have you checked for single edges? Any gaps in your model will certainly lead to failure.
Also, do a visual check and make sure that you have...
|
Forum: ANSYS Meshing & Geometry
March 31, 2017, 17:11
|
Replies: 1
Views: 875
Hey Vishal,
ICEM CFD Hexa uses the separate...
Hey Vishal,
ICEM CFD Hexa uses the separate blocking layer and associates it with the geometry. Therefore, if you are adding geometry, you will need to associate your blocking with that new...
|
Forum: ANSYS Meshing & Geometry
March 16, 2017, 10:24
|
Replies: 42
Views: 49,735
|
Forum: ANSYS Meshing & Geometry
January 24, 2017, 10:10
|
Replies: 31
Views: 16,673
|
Forum: FLUENT
June 18, 2015, 12:41
|
Replies: 10
Views: 2,114
It looks to me like you did a great job, but...
It looks to me like you did a great job, but found something very strange. I don't think the issue has anything to do with octree or copying it a specific distance back...
Does the mesh actually...
|
Forum: ANSYS Meshing & Geometry
December 31, 2014, 09:45
|
Replies: 15
Views: 8,086
|
Forum: ANSYS Meshing & Geometry
December 12, 2014, 09:33
|
Replies: 3
Views: 2,259
Yup, assuming you have version 15.0 or newer,...
Yup, assuming you have version 15.0 or newer, check out the component system called "External Model". This system lets you attach meshes of various formats and then you can connect a mechanical...
|
Forum: ANSYS Meshing & Geometry
December 12, 2014, 09:29
|
Replies: 8
Views: 2,789
|
Forum: ANSYS Meshing & Geometry
December 11, 2014, 10:22
|
Replies: 10
Views: 5,801
|
Forum: ANSYS Meshing & Geometry
December 11, 2014, 10:17
|
Replies: 12
Views: 1,874
Sure... The red pipe is not a problem. OGrids...
Sure... The red pipe is not a problem. OGrids are the secrete here also. But first, does the red pipe inject fluid into the mixer (is it open)? Or is it really just an obstacle? It would cause a...
|
Forum: ANSYS Meshing & Geometry
December 11, 2014, 10:04
|
Replies: 10
Views: 5,801
|
Forum: ANSYS Meshing & Geometry
December 10, 2014, 18:07
|
Replies: 2
Views: 1,469
|
Forum: ANSYS Meshing & Geometry
December 10, 2014, 18:04
|
Replies: 12
Views: 1,874
|
Forum: ANSYS Meshing & Geometry
December 9, 2014, 15:55
|
Replies: 6
Views: 2,429
Yup, I agree. As a general question, ANSYS...
Yup, I agree. As a general question, ANSYS Meshing is the right answer. It actually includes much of the ICEM CFD technology under the hood (along with great technology from other sources), it is...
|
Forum: ANSYS Meshing & Geometry
December 2, 2014, 08:49
|
Replies: 10
Views: 3,927
Yes, if you want the mesh to be periodic, you...
Yes, if you want the mesh to be periodic, you need to define periodic verts...
However, if your solver is able to define periodicity without periodic mesh, then you can get away without it.
...
|
Forum: ANSYS Meshing & Geometry
November 24, 2014, 08:34
|
Replies: 3
Views: 2,313
Settings => Product
You will find a "Blocking" checkbox under "Settings => Product"...
Turn it on and then restart ICEM CFD...
|
Forum: ANSYS Meshing & Geometry
February 25, 2014, 14:43
|
Replies: 3
Views: 3,399
"Min Angle" quality in pre-mesh is the same...
"Min Angle" quality in pre-mesh is the same quality diagnostic which is used under mesh quality. It computes minimum internal angle.
Looking at the code, the "Angle" diagnostic in pre-mesh shows...
|
Forum: ANSYS Meshing & Geometry
October 24, 2013, 15:50
|
Replies: 10
Views: 3,180
Oh yea, the shell mesh offset is really just...
Oh yea, the shell mesh offset is really just designed for bolt holes (FEA), not 2D N-S flow...
Instead, try using "blayer2D" to generate higher quality boundary layers. There are a number of...
|
Forum: ANSYS Meshing & Geometry
October 23, 2013, 22:02
|
Replies: 10
Views: 3,180
|
Forum: ANSYS Meshing & Geometry
October 19, 2013, 20:49
|
Replies: 2
Views: 1,609
|
Forum: ANSYS Meshing & Geometry
October 16, 2013, 20:27
|
Replies: 10
Views: 3,927
|
Forum: ANSYS Meshing & Geometry
October 11, 2013, 09:04
|
Replies: 8
Views: 3,366
|
Forum: ANSYS Meshing & Geometry
October 11, 2013, 09:01
|
Replies: 2
Views: 1,247
Normally, I would just say "don't worry about...
Normally, I would just say "don't worry about it", but your blocking does look strange.
I am guessing you didn't create these with top down splits... How did you create these? Are they con...
|
Forum: ANSYS Meshing & Geometry
October 10, 2013, 10:29
|
Replies: 6
Views: 4,295
|